Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
REAR CASTER DOLLY/TOOL HOLDER
AND FRONT CASTER FEET ASSEMBLY
(Not standard with all models)
You will find four casters (a), two caster feet (b), rear caster dolly/tool holder (c), and four
screws with your wet/dry vacuum. Assemble as follows:
a
b
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down
so that the bottom is facing up.
2. Take rear caster dolly and place into slots (on rear of tank, opposite of drain) and secure
with screws provided (Figure 1).
3. If flatwashers are included in hardware package place flatwasher over stem of caster
before installing casters into feet.
NOTE: flatwashers are not required with all units.
4. Insert casters into bottom of rear caster dolly by placing stem of caster into holes pro-
vided. Apply pressure and twisting motion until casters snap into place (Figure 2).
5. With tank drain facing you, take caster foot marked with the letter A (Figure 3) and place
in slot on left side of tank also marked with the letter A and secure with screw provided
(Figure 4).
6. Take caster foot marked with the letter B (Figure 5) and place in slot on right side of tank
also marked with the letter B and secure with screw provided (Figure 6).
7. If flatwashers are included in hardware package place flatwasher over stem of caster
before installing casters into feet.
NOTE: flatwashers are not required with all units.
8. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 7).
9. Return tank to upright position.
10. Place tool basket (Not standard with all models) with curved surface against tank on
rear caster dolly assembly
(Figure 8).
1
2
4
5
7
REAR WHEEL DOLLY/TOOL HOLDER
AND FRONT CASTER FEET ASSEMBLY
(Not standard with all models)
You will find two casters (d.), two large rear wheels (e.), one axle (f.), rear dolly/
basket (g.), two caster feet (h.) and four screws with your wet/dry vacuum. Assemble as follows:
ASSEMBLY
c
3
6
8
d
e
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so that
the bottom is facing up.
2. Place axle upright on a hard surface and hammer on (1) cap nut. Place (1) wheel on axle and slide
down to cap nut (Figure 9). Be sure flat side of wheel hub is facing outward.
3. Slide axle through holes provided in dolly/basket (Figure 10).
4. Slide remaining wheel onto axle and hammer on second cap nut (Figure 11).
5. Take rear dolly assembly and place into slots (on rear of tank opposite drain) and secure with
screws provided (Figure 12).
6. With tank drain facing you, take caster foot marked with the letter A (Figure 13) and place
in slot on left side of tank also marked with the letter A and secure with screw provided
(Figure 14).
7. Take caster foot marked with the letter B (Figure 15) and place in slot on right side of tank
also marked with the letter B and secure with screw provided (Figure 16).
8. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 17).
9. Return tank to upright position.
9
10
13
14
REAR WHEEL DOLLY/TOOL HOLDER
AND FRONT CASTER FEET ASSEMBLY
FOR METAL TANkS
(Not standard with all models)
You will find two casters (i.), two large rear wheels (j.), one axle (k.), rear dolly (l.), two
caster feet (m.) and four screws with your wet/dry vacuum. Assemble as follows:
i.
j.
1.
With cord disconnected from receptacle and tank cover removed, turn tank upside down
so that the bottom is facing up.
2.
Place axle upright on a hard surface and hammer on (1) cap nut. Place (1) wheel on axle
and slide down to cap nut (Figure 18). Be sure flat side of wheel hub is facing outward.
3.
Slide axle through holes provided in dolly (Figure 19).
Slide remaining wheel onto axle and hammer on second cap nut (Figure 20).
4.
5.
With a pair of scissors, trim the enclosed template to fit your size tank. Sizes will be 11",
14" or 16" diameters.
6.
Once template is cut out, place on bottom of tank, align inlet arrow on template with
center of inlet on tank (Figure 21).
7.
Align cutouts in center of rear dolly with bars on template (Figure 22).
8.
Place groove of rear dolly over rim of tank and push until the dolly is tight against bot-
tom of tank (Figure 23).
9.
Secure dolly with screw and washer provided (Figure 24).
10. If caster feet are attached together, separate by removing webbing.
11. Take caster foot marked with the letter A and align arrow on foot (Figure 25) with arrow
on template also marked with the letter A (Figure 26).
12. Place groove of foot over rim of tank and push until the caster foot is tight against
bottom of tank (Figure 27).
13. Secure feet with screw and washer provided (Figure 28).
4
g
f
11
12
15
16
k.
l.
h
17
m.
Publicidad
Tabla de contenido
