Technical Data; Before Starting The Equipment - EINHELL GE-CR 30 Li Solo Manual De Instrucciones

Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

See warranty card of your country.
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect con-
ditions.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
Anleitung_GE_CR_30_Li_Solo_SPK8.indb 27 Anleitung_GE_CR_30_Li_Solo_SPK8.indb 27
GB
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

Caution!
The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
Power-X-Change
•
18 V, 1.5 Ah, 5 lithium-ion cells
•
18 V, 2.0 Ah, 5 lithium-ion cells
•
18 V, 3.0 Ah, 10 lithium-ion cells
•
18 V, 4.0 Ah, 10 lithium-ion cells
•
18 V, 5.2 Ah, 10 lithium-ion cells
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Warning!
Always pull out the safety plug before making ad-
justments or carrying out maintenance, cleaning
and repair work on the equipment.
Assembly (Figs. 3a-3g)
•
Pull out the split pin (Fig. 3a/Item A) and re-
move the pin (Fig. 3a/Item B). Push the brake
shoe (Fig. 3b/Item 12) into the mount and fix it
in position with the pin and split pin previously
removed.
•
Undo the eight Philips screws (Fig. 3b/Pos.
C) with washers on both sides of the axle.
On both sides, push the transport wheel as
shown in Fig. 3c onto the axle and secure
with the Philips screws and washers (see Fig.
3c inset).
•
Press the wheel caps (Fig. 3d/Item 11) onto
the transport wheels.
- 27 -
02.08.2017 11:30:40 02.08.2017 11:30:40