Important; Operation - EINHELL GE-CR 30 Li Solo Manual De Instrucciones

•
Push the lower push bar as shown in Fig. 3e
onto the motor unit (Fig. 3e/Item 3) and se-
cure with the screws (Fig. 3e/Item 9) and the
star nuts (Fig. 3e/Item 8).
•
Push the upper push bar (Fig. 3f/Item 1) onto
the lower push bar (Fig. 3f/Item 2) and secure
with the screws (Fig. 3f/Item 9) and the star
nuts (Fig. 3f/Item 8).
•
Secure the cable to the push bars with 2
cable clips (Fig. 3g/Item 7).
Charging the battery (Fig. 4a/4b)
The equipment is supplied without batteries and
without a charger.
1. Take the battery pack out of the equipment.
To do so, press the pushlock button (Fig. 4a/
Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack into the charger.
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Installing the battery (Fig. 4c-4d)
Open the battery cover. This is done by pressing
the lock release (A) as shown in Fig. 4b and swin-
ging up the cover. Then connect the two batteries
into the mounts as shown in Fig. 4d and push
them forward until you hear the batteries engage.
Anleitung_GE_CR_30_Li_Solo_SPK8.indb 28 Anleitung_GE_CR_30_Li_Solo_SPK8.indb 28
GB

Important!

Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two bat-
teries must always be fully charged before use.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
Battery capacity indicator (Fig. 4a)
Press the switch for the battery capacity indicator
(Fig. 4a/Item A). The battery capacity indicator
(Fig. 4a/Item B) shows the charge status of the
battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack!

6. Operation

Caution!
The device is equipped with a safety switch to
prevent unauthorized use. Immediately before
using the device, insert the safety plug (Fig. 5/
Item 5). Remove the safety plug again when inter-
rupting or terminating your work. To do so, press
the lug (Fig. 5/Item A).
Danger! To prevent accidental start-up of the ma-
chine, the push-bar is equipped with a two-point
switch (Fig. 10/Item A) which must be pressed
before the lever switch (Fig. 10/Item B) can be
pressed. If the lever switch is released, the machi-
ne switches off . Repeat this process several times
so that you are sure that your machine functions
properly. Before you perform any repair or mainte-
nance work on the machine, ensure that the hoe
blades are not rotating and that the power supply
is disconnected.
The equipment must be moved into operating
position before you begin with your work. First pull
the locking pin (Fig. 11/Item A) in the direction of
- 28 -
02.08.2017 11:30:40 02.08.2017 11:30:40