Preface; Introduction; Identification Of The Product; Transport Of The Machine - PLYMOVENT MFS Instrucciones Para El Uso

pREFaCE

using this manual
This manual is intended to be used as a work of reference for
professional, well trained and authorised users to be able to
safely install, use, maintain and repair the product mentioned
on the cover of this document.
pictograms and symbols
The following pictograms and symbols are used in this manual:
TIp
Suggestions and recommendations to simplify
carrying out tasks and actions.
CauTION!
Procedures, if not carried out with the necessary
caution, could damage the product, the workshop or
the environment.
waRNINg!
Procedures which, if not carried out with the
necessary caution, may damage the product or
cause serious personal injury.
waRNINg!
Denotes risk of electric shock.
waRNINg!
Important warning to prevent fire.
Service and technical support
For information about specific adjustments, maintenance or
repair jobs which are not dealt with in this manual, please
contact the supplier of the product. He will always be willing to
help you. Make sure you have the following specifications at
hand:
- product name
- serial number
These data can be found on the identification plate.
1

INTRODuCTION

1.1

Identification of the product

The identification plate contains, among other things, the
following data:
- product name
- serial number
- supply voltage and frequency
- power consumption
1.2 general description
The MFS (MFS/C) is a mobile filter unit with integrated fan that
provides extraction and filtration for use with a flexible
extraction arm or extraction hose. The machine features an
aluminum spark arrester and a round cellulose filter cartridge.
This filter cartridge is provided with a precoat to extend the
lifespan and increases initial operating efficiency of the filter.
The machine is fitted with a RoboClean system for automatic
sectionwise cleaning of the filter cartridge by compressed air.
In case of an MFS the compressed air is externally supplied,
whereas the MFS/C is equipped with a built-in compressor. The
dust and dirt particles end up in the dust tray underneath the
unit.
Thanks to the four transport wheels (two of which are swivel
casters), the MFS (MFS/C) is extremely suitable to be used in
relatively small facilities or near sources of pollution without a
fixed location. Extraction arm/hose to be ordered separately.
0507260010/301113/G MFS - MFS/C
1.3 product combinations
In order to operate the machine, selection of one of the
following products is required:
- Flex-3 (extraction arm)
- Flex-4 (extraction arm)
- UltraFlex-3 (extraction arm)
- UltraFlex-4 (extraction arm)
- SUS-5/203 (extraction hose)
1.4 Options and accessories
There are no options and accessories available.
1.5 Technical specifications
Dimensions L x W x H
Weight
Power consumption
Unrestricted airflow
Net extraction capacity
Min. airflow
Motor speed
Filter class:
- spark arrester
- main filter DuraFilter FCC-30
Filter surface
Required compressed air quality
Required pressure
Compressed air consumption
Insulation class
Protection class
Refer to the available product data sheet for
detailed specifications.
1.6 ambient conditions
Min. operating temperature
Nom. operating temperature
Max. operating temperature
Max. relative humidity
1.7

Transport of the machine

The manufacturer cannot be held liable for any transportation
damage after delivery of the machine. Always handle the
machine and the accompanying extraction arm/hose with care.
Always completely dismount the extraction arm/hose before
transport. Dismount the arm/hose by executing the mounting
procedure in reverse order. Subsequently the machine and the
arm/hose can be transported on a pallet in the original
packing.
To prevent damage, prevent the machine and the arm/hose
from shifting on the pallet.
2

pRODuCT DESCRIpTION

2.1 Components
The machine consists of the following main components:
Fig. 2.1
A control panel
B control panel cover
1210 x 810 x 1020 mm
- MFS: 105 kg
- MFS/C: 115 kg
0,75 kW
2400 m /h
3
1250 m /h (clean filter)
3
600 m /h
3
2800 rpm
- G2 according to DIN-EN 779
- M according to NEN-EN-IEC
60335-2-69
30 m
2
dry and oil-free according to ISO
8573-3 klasse 6
400-500 kPa (4-5 bar)
60 nl/min.
F
IP 50
5°C (41°F)
20°C (68°F)
45°C (113°F)
80% (non condensing)
EN - 3