Panasonic SC-HC28 Instrucciones De Funcionamiento página 11

Radio
A beat sound or noise is heard while receiving
radio broadcast.
≥ Confirm the antenna is properly connected. (l 5)
≥ Adjust the position of the antenna.
≥ Try to keep a certain amount of distance between the antenna and
AC mains lead.
≥ Try using an outdoor antenna if there are buildings or mountains
nearby.
≥ Switch the television or other audio players off or separate it from
this unit.
≥ Keep this unit away from mobile phones if the interference is
apparent.
[SC-HC28]
iPod/iPhone/iPad operations
Cannot charge or operate.
≥ Have you selected the appropriate selector?
Press [iPod] to select either "IPOD_DOCK" or "IPOD_PORT".
≥ Check that the iPod/iPhone/iPad is connected properly. (l 6)
≥ The battery of the iPod/iPhone/iPad is depleted. Charge the iPod/
iPhone/iPad, and then operate again.
≥ Connect the iPod/iPhone/iPad again or try to restart the iPod/
iPhone/iPad.
≥ When this unit is in standby mode, charging will not start when
using the "IPOD_PORT" connection.
Turn this unit on and make sure the charging has started before
switching this unit to standby mode.
Remote control
The remote control doesn't work properly.
≥ The remote control and this unit are using a different code.
(l right, "REMOTE ")
≥ Is the battery depleted or is the battery inserted incorrectly? (l 4)
Messages
The following messages or service numbers may
appear on the unit's display.
"--:--"
≥ You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (l 9).
"ADJUST CLOCK"
≥ Clock is not set. Adjust the clock accordingly.
"ADJUST TIMER"
≥ Play timer is not set. Adjust the play timer accordingly.
"AUTO OFF"
≥ The unit has been left unused for about 30 minutes and will shut
down within a minute. Press any button to cancel it.
[SC-HC28] "CHECKING CONNECTION"
≥ The unit is checking the connected iPod/iPhone/iPad.
≥ If this display keeps appearing, make sure that the battery of the
iPod/iPhone/iPad is not depleted and that the iPod/iPhone/iPad is
turned on and connected correctly (l 6).
[SC-HC28]
"DOCK OPEN"
≥ Is the dock open? Close the dock completely to open the sliding
door.
"ERROR"
≥ Incorrect operation is performed. Read the instructions and try
again.
"F " (" " stands for a number.)
≥ There is a problem with this unit.
Note down the displayed number, disconnect the AC mains lead
and consult your dealer.
"ILLEGAL OPEN"
≥ Sliding door is not in correct position. Turn the unit off and on
again. If this display appears again, consult the dealer.
[SC-HC28]
"IPOD_DOCK OVER CURRENT ERROR"
"IPOD_PORT OVER CURRENT ERROR"
≥ The iPod/iPhone/iPad is drawing too much power. Disconnect the
iPod/iPhone/iPad and turn the unit off and on again.
≥ The USB device is drawing too much power. Switch to "CD"
mode, remove the USB and turn the unit off.
"NODEVICE"
≥ [SC-HC28] The iPod/iPhone/iPad device is not inserted correctly.
Read the instructions and try again (l 6).
≥ [SC-HC28] The battery of the iPod/iPhone/iPad is depleted. Charge
the iPod/iPhone/iPad and turn it on before connecting.
≥ The USB device is not inserted. Check the connection.
"NO DISC"
≥ Insert the disc to be played (l 6).
"NO PLAY"
≥ A CD that is not in CD-DA or MP3 format is inserted. It cannot be
played.
≥ If there are more than 255 albums or folders (audio and
non-audio), some of the MP3 files in these albums may not be
read and played. Transfer these music albums to another USB.
Alternatively, reformat the USB device and save these music
albums prior to saving the other non-audio folders.
[SC-HC28] "NOT SUPPORTED"
≥ You have connected an iPod/iPhone/iPad that cannot be played
(l 12).
≥ If the iPod/iPhone/iPad is compatible, turn it on and connect it
correctly.
"READING"
≥ The unit is checking the CD information. After this display has
disappeared, start operating.
"REMOTE " (" " stands for a number.)
≥ The remote control and this unit are using different codes. Change
the code on the remote control.
– When "REMOTE 1" is displayed, press and hold [OK] and
[RADIO] for more than 4 seconds.
– When "REMOTE 2" is displayed, press and hold [OK] and [CD]
for more than 4 seconds.
[SC-HC18] "USB OVER CURRENT ERROR"
≥ The USB device is drawing too much power. Switch to "CD"
mode, remove the USB and turn the unit off.
11
RQT9734