Tabla De Contenido; Before Using; Cautions On Installation; Cautions On Handling - Denon AVR-1604 Instrucciones De Operación

We greatly appreciate your purchase of the AVR-1604.
2
2 To be sure you take maximum advantage of all the features the AVR-1604 has to offer, read these
instructions carefully and use the set properly. Be sure to keep this manual for future reference,
should any questions or problems arise.
"SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE
CABINET FOR FUTURE REFERENCE"
INTRODUCTION
2
Thank you for choosing the DENON A/V Surround receiver. This remarkable component has been engineered to
provide superb surround sound listening with home theater sources such as DVD, as well as providing
outstanding high fidelity reproduction of your favorite music sources.
As this product is provided with an immense array of features, we recommend that before you begin hookup and
operation that you review the contents of this manual before proceeding.
TABLE OF CONTENTS
z
Before Using........................................................3
x
Cautions on Installation........................................3
c
Cautions on Handling...........................................3
v
Features ...............................................................4
b
Part Names and Functions ..............................4, 5
n
Read this First......................................................5
m
Setting up the Speaker Systems .........................5
,
Connections ..................................................6 ~ 9
.
Using the Remote Control Unit ...........................9
⁄0
Setting up the System ..............................10 ~ 14
2 ACCESSORIES
Check that the following parts are included in addition to the main unit:
q Operating instructions........................................1
w Service station list..............................................1
e Remote control unit (RC-941) ............................1
e r
All manuals and user guides at all-guides.com
⁄1
Remote Control Unit .................................15 ~ 17
⁄2
Operation...................................................17 ~ 20
⁄3
Surround....................................................20 ~ 25
⁄4
DSP Surround Simulation..........................26 ~ 28
⁄5
Listening to the Radio ...............................29 ~ 32
⁄6
Last Function Memory.......................................32
⁄7
Initialization of the Microprocessor....................32
⁄8
Additional Information ...............................33 ~ 36
⁄9
Troubleshooting .................................................36
¤0
Specifications.....................................................37
List of Preset Codes ....................................248 ~ 250
r R6P/AA batteries................................................2
t AM loop antenna................................................1
y FM indoor antenna.............................................1
t y
1

BEFORE USING

Pay attention to the following before using this unit:
• Moving the set
To prevent short circuits or damaged wires in the
connection cords, always unplug the power supply
cord and disconnect the connection cords between
all other audio components when moving the set.
• Before turning the power operation switch on
Check once again that all connections are proper
and that there are not problems with the connection
cords. Always set the power operation switch to the
standby position before connecting and disconnecting
connection cords.
2

CAUTIONS ON INSTALLATION

Noise or disturbance of the picture may be generated
if this unit or any other electronic equipment using
microprocessors is used near a tuner or TV.
If this happens, take the following steps:
• Install this unit as far as possible from the tuner or
TV.
• Set the antenna wires from the tuner or TV away
from this unit's power supply cord and input/output
connection cords.
• Noise or disturbance tends to occur particularly
when using indoor antennas or 300 Ω/ohms feeder
wires. We recommend using outdoor antennas
and 75 Ω/ohms coaxial cables.
For heat dispersal, leave at least 10 cm of space
between the top, back and sides of this unit and
the wall or other components.
3

CAUTIONS ON HANDLING

• Switching the input function when input jacks
are not connected
A clicking noise may be produced if the input
function is switched when nothing is connected to
the input jacks. If this happens, either turn down the
MASTER VOLUME control or connect components
to the input jacks.
• Muting of PRE OUT jack, HEADPHONE jack and
SPEAKER terminals
The PRE OUT jack, HEADPHONE jack and SPEAKER
terminals include a muting circuit. Because of this,
the output signals are greatly reduced for several
ENGLISH
• Store this instructions in a safe place
After reading, store this instructions along with the
warranty in a safe place.
• Note that the illustrations in this instructions
may differ from the actual set for explanation
purposes.
• V. AUX terminal
The AVR-1604's front
panel is equipped with
a V. AUX terminal.
Remove the cap
covering the terminal
when you want to use
it.
10 cm or more
10 cm or more
seconds after the power operation switch is turned
on or input function, surround mode or any other set-
up is changed. If the volume is turned up during this
time, the output will be very high after the muting
circuit stops functioning. Always wait until the
muting circuit turns off before adjusting the volume.
• Whenever the power operation switch is in the
£ OFF or STANDBY state, the apparatus is still
connected on some AC line voltages.
Please be sure to unplug the cord when you
leave home for, say, a vacation.
wall
3