Inserting Batteries - Revell Control MOSTER TRUCK DARK GIANT Manual Del Usuario

Required batteries for the vehicle:
Power supply:
Rated output: DC 9,6 V / 700 mAh
Batteries: 1 x 9,6 V rechargeable
NiMH battery (included)
Capacity: 700 mAh
Charging unit technical data: Suitable for NiMH batteries 9.6 V / from 500 mAh
1 vehICle
1A Giant off-road 1C Bumper
tyres
1D ON/OFF switch
1B Bodywork
1E Battery cover
3 aCCeSSorIeS
3A Charging unit
3B NiMH battery
5 aSSeMbly
Wheels: Attach the wheels to the axles (noting the rolling direction, 5A). Secure the
wheels using the enclosed screws by inserting them in the hub and screwing them tight
with a screwdriver (5B).
Bodywork: Slide one of the clips on each bodywork mount at a height of five grooves
from the bottom (5C). Now sit the bodywork on the mounts and secure it with another clip
on each mount (5D).
6 CHARGING THE VEHICLE BATTERY
Attention: Before charging and after each use, the battery and the motor must cool down
for 10 to 15 minutes. Otherwise, the battery or motor can be damaged. Do not leave the
charging process unsupervised.
6A Switch off the remote control and vehicle!
6B Unscrew the battery cover.
6C Remove the battery from the vehicle and unplug the cable.
6D Connect the charger to the battery and plug the charger into a socket; the LED on the
charger lights up. The charging process is complete when the LED goes completely out
and the battery is slightly warm to the touch. Disconnect the battery from the charger
and then unplug the charger from the socket.
6E Replace the battery in the vehicle, plug it in and screw the battery cover back into place.
After a charge time of approx. 240 – 300 minutes, the vehicle can drive for around
15 – 20 minutes, depending on the driving style. if the battery is empty, the car
stops in order to prevent a harmful total discharge of the battery.
14
Battery requirements
for the controller:
Power supply:
Rated output: DC 6 V
Batteries: 4 x 1,5 V „AA"
(not included)
2 reMoTe CoNTrol
2A Power LED 2C Left stick
2B ON/OFF switch 2D Right stick

4 INSerTINg baTTerIeS

4A Unscrew the cover.
4B Insert 4 x 1.5 V AA batteries
and pay attention to the polarity
specification, as shown in the
battery compartment.
4C Close the battery compartment
cover and tighten the screw.
7 STarT preparaTIoN
Begin by switching on the ON/OFF switch
on the remote control; the power LED will
flash (7A). Then switch the ON/OFF on
the vehicle to the "ON" position (7B).
As soon as the power LED on the remote
control is permanently lit, the vehicle is
connected to the remote control and
ready to drive.
8 STeerINg TrIM adjuSTMeNT
The left stick controls the left wheels; the right stick controls the right wheels.
8A Driving forwards / backwards:
To drive forwards, carefully push both sticks forward.
To drive faster, carefully push the sticks further forward.
To drive backwards, carefully push both sticks back.
To drive faster, carefully push the sticks further back.
8B Turning:
To turn left, carefully push the right stick forward and let the left stick go. To keep turning
further left, carefully push the right stick forward and push the left stick a little forward
(not as far as the right stick). Operate the controls the other way around to turn right.
8C Turning on the spot:
Carefully push one stick forward and the other just as far back. This works in both directions.
INSTruCTIoNS For SaFe drIvINg
GENERAL DRiViNG TipS:
• Always move the controls slowly and with a gentle touch.
• Always maintain visual contact with the vehicle and do not look at the remote control!
• On initial driving attempts, there is a general tendency toward excessive movements
of the controls. Make sure that you have sufficient room.
• In order to drive along a curve, it often suffices to turn the controller very slightly in
the respective direction.
• Driving training: Ideally, you should practice on a large, empty parking lot. Set up
two empty plastic bottles approx. 5-10 metres apart. Now try to drive the vehicle
around these two bottles – as close as possible without knocking the bottles over.
In the process, carefully increase the speed. After you have drained the batteries
approximately two to three times for this process, you will be able to control your
vehicle better.
After a crash, always release the speed control immediately in order to prevent
damage to the electronics.
When switching off, always switch off
the vehicle first (cf. 7B), then the remote
control (cf. 7A)! Otherwise, a drive
command can accidentally be triggered,
causing the vehicle to drive away on
its own, which can lead to considerable
damage.
15