Surtek HL732 Manual De Usuario Y Garantía página 17

area to smaller sections and clean each section
one at a time. Allow the detergent to rest on
the surface for a few minutes and then rinse
at high pressure. DO NOT LET THE CLEANSER
DRY. Always clean from left to right and top to
bottom for best results. Rinse at high pressure
using the fan spray keeping the tip of the spray
nozzle at least 6-9 inches from the cleaning
surface. Maintain a further distance from the
cleaning area when using a direct spray.
CAUTION: For softer woods, increase the
distance from the cleaning area.
CEMENT PATIOS, STONE, AND BRICK
Rinse cleaning and surrounding area with fresh
water. If using detergent, fill the detergent
reservoir and apply to the area being cleaned
at low pressure. Rinse at high pressure using
the fan spray in a sweeping motion keeping
the tip of the spray nozzle at least 3-6 inches
from the cleaning surface. Maintain a further
distance from the cleaning area when using a
direct spray.
CARS, BOATS, AND MOTORCYCLES
Rinse cleaning and surrounding area with fresh
water. If using detergent, fill the detergent res-
ervoir and apply to the area being cleaned at
low pressure. To achieve the best results, clean
one side at a time. Allow the detergent to rest
on the surface for a few minutes, but do not let
the detergent dry. Rinse at high pressure using
the fan spray in a sweeping motion keeping the
tip of the spray nozzle at least 8 inches from the
cleaning surface. Maintain a further distance
from the cleaning area when using a direct
spray. Wipe surface dry for a polished finish.
IMPORTANT: Only use liquid detergent, DO
NOT use regular detergent.
BARBECUE GRILLS, POWER EQUIPMENT, AND
GARDEN TOOLS
Rinse cleaning and surrounding area with fresh
water. If using detergent, fill the detergent
reservoir and apply to the area being cleaned
at low pressure. Allow the detergent to rest on
the surface for a few minutes, but do not let the
detergent dry. Rinse at high pressure using the
fan spray keeping the tip of the spray nozzle at
least 1-3 inches from the cleaning surface.
Maintain a further distance from the cleaning
area when using a direct spray.
SHUTTING DOWN
1. After each use, if you have applied chemicals,
place chemical hose into container of clean
water and run clean water through chemical
injection system to flush the system thoroughly.
E N G L I S H •
NOTE: Failure to do s o could cause damage to
the pump.
2. Switch the motor in the OFF position, or pull
out the plug to stop the motor.
NOTE: NEVER turn the water off with the unit
is in running.
3. Turn water source off.
4. Pull trigger on spray gun to re lieve any water
pressure.
5. See storage section in this manual for proper
storage procedures.
MAINTENANCE
CHANGING THE PUMP OIL
CAUTION: PROLONGED EXPOSURE TO USED
OIL IS DANGEROUS, ALWAYS WASH YOUR
HANDS THOROUGHLY AFTER HANDLING USED
OIL.
1. Unscrew and remove the oil filler cap.
2. Place the oil collection tray (not supplied)
under the drain cap.
3. Unscrew the drain cap, and allow the used
oil to drain from the crankcase into the oil
collection tray.
NOTE: Drain the oil when the engine is warm,
this will ensure the oil flows out quicker.
4. Replace the drain plug and its ring seal.
5. With the power washer in a level position,
fill to the centre of the sight glass with the
recommended oil.
6. Replace the oil filler cap.
ENVIRONMENTAL PROTECTION
One of the most damaging sources of pollution
is oil. Do not throw away used oil with your
domestic rubbish or down drains and sinks.
Place it in a leak proof container and take it to
you local waste disposal site.
CHECKING HIGH PRESSURE HOSE
The high pressure hose can develop leaks
from wear, kinking, or abuse. Inspect the
hose each time before using it. Check for cuts,
leaks, abrasions or bulging of cover, damage
or movement of couplings. If any ofthese
conditions exist, replace the hose immediately.
CHECK DETERGENT SIPHONING TUBE
Examine the filter on the detergent tube and
clean if clogged. The tube should fit tightly on
the barbed fitting. Examine the tube for leaks
or tears. Replace the filter or tube if either is
damaged.
CHECK GUN AND NOZZLE EXTENSION
Examine the hose connection to the spray gun
and make sure it is secure. Test the trigger by
pressing it and making sure it springs back into
place when you release it.
U s er 's M an u al
17