TZS First AUSTRIA FA-5475-1 Manual De Instrucciones página 2

OPERATION INSTRUCTIONS FOR ESPRESSO/CAPPUCCINO/COFFEE MAKER
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire,
electric shock, and/or injury to persons, including the following:
1. Read all instructions before using the machine.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against electric shock, do not immerse cord, plugs, or machine in water or other liquid.
4. Close super vision is necessary when any appliance is used by or near children.
5. Turn control switch to OFF and unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning.
6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been
damaged in any manner. Return this appliance only to the nearest authorized service center for repair.
7. Do not use outdoors.
8. Do not let cord hang over edge of table or counter, or touch hot surfaces.
9. Do not place this appliance on or near a hot gas or electric burner or in a heated oven.
10. To disconnect, turn any control to "off", then remove plug from wall outlet.
11. Do not use appliance for other than intended use.
12. Use on a hard, flat level surface only, to avoid interruption of air flow underneath the appliance.
13. Always be sure water tank boiler cap is tightened securely before turning machine on.
14. DO NOT remove boiler cap until pressure is completely relieved. See section "CAUTION PRESSURE".
15. WARNING: To reduce the risk of fire or electric shock, do not remove any service covers. No user
serviceable parts inside. Repair should be done by authorized personnel only.
16. The use of accessory attachments not recommended by the appliance manufacturer may result in lire,
electric shock or injury to persons.
17. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
18. Children should be supervised to ensure that they do not play with the appliance.
SAVE THESE INSTRUCTIONS
SPECIAL CORD SET INSTRUCTIONS
a) A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting
from becoming entangled in or tripping over a longer cord.
b) Longer detachable power-supply cords or extension cords are available and may be used if care is
exercised in their use.
c) If a long detachable power-supply corf or extension cord is used.
1. The marked electrical rating of the detachable power–supply cord or extension cord should be at least
as great as the electrical rating of the appliance.
2. If the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord,
and
3. The longer cord should be arranged so that it will not drape over the counter top or table top where it
can be pulled on by children or tripped over.
d) "This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric
shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the
outlet, reverse the plug. If it still dose not fit, contact a qualified electrician. Do not attempt to modify the
plug in any way."
CAUTION: PRESSURE
To avoid possible burns from hot steam and water, NEVER open the boiler cap while there is pressure in the
boiler. Remove all pressure first.
To remove all pressure, proceed as follows:
1. Turn the selector knob to the "O" position and unplug the appliance.
2. Remove the filter holder and dispose of coffee grounds.
3. Re-install the filter holder and the empty carafe.
4. Turn the steam selector control knob to the "cup" position and allow all pressure and residual water to
completely drain off into the carafe until all flow and sound ceases. The pressure is now removed.
INTRODUCTION
Congratulations! You are the owner of an espresso/cappuccino maker. This unique appliance has been
designed to provide you with delicious espresso/cappuccino quickly and conveniently.
2
Preparing espresso or cappuccino is very different from brewing regular drip coffee in that this machine
operates pressure and requires special attention. To ensure your safety and the long life of this appliance,
please read all instructions, cautions, notes, and attentions.
PRODUCT FEATURES AND DIAGRAM PARTS
1. Water tank boiler cap 5. Carafe set
2. Steam selector control knob 6. Braw head
3. Indicator light 7. Frothing tube
4. Filter holder set 8. Carafe lid
HOW TO PREPARE QUALITY ESPRESSO AND CAPPUCCINO AT HOME
The Coffee:
The coffee should be freshly ground, dark roasted variety. Pre-ground coffee will only retain its flavor for 7-8
days, provided it is stored in an air tight container, in a cool, dark area. Do not store in a refrigerator freezer.
Whole beans are recommended, to be ground just before use. Coffee beans stored in an air tight container will
keep up to 4 weeks before they being to lose their flavor.
The Grind:
This is a vital step in the espresso making process and takes practice. The coffee must be ground fine, but
not too fine
• The correct grind should look gritty, like salt or sand.
• If the grind is too fine, the water will flow through the coffee even under pressure. This grind looks like
powder and feels like flour when rubbed between fingers.
• If the grind is too coarse, the water flows through the coffee too fast, preventing a full flavored extraction.
Be sure to use a quality grinder or mill for uniform consistency in your espresso grind. Oval shaped coffee mills
are not recommended because the grind is not consistent.
MAKE ESPRESSO COFFEE
1. Remove the tank cover by turning it in anti-clockwise. Pour appropriate water in water tank with the carafe.
Do not exceed the maximum capacity.
Note:
• The carafe has the cup marks, the maximum tank capacity is equal to 4 cups marks water quantity. The
minimum tank capacity is equal to 2 cups marks water quantity.
• Before pouring the water into the water tank, be sure the power cord is unplug from the power outlet and
the steam knob is in the (see Fig. 2/3) position.
2. Replace the tank cover in place by turning the cover in clockwise until it locks in position.
3. Put the steel mesh into metal funnel, add coffee powder to steel mesh with measuring spoon, a spoon
coffee powder can make about a cup of top-grade coffee. Then press the coffee powder tightly with the
tamper.
Note: Select your desired coffee powder to make desired cups coffee, the steel mesh has 2 cups and 4 cups
marks.
4. Make sure the tubers on the funnel align with the grooves in the appliance, then insert the funnel into from
the "INSERT" position, and you can fix the funnel into coffee maker firmly through turn it anti-clockwise until
it is locked in the "LOCK" position.
5. Place the carafe on the removable shelf.
6. Plug the power cord into the outlet.
Turn the steam knob to (see Fig. 2/1) position, and the indicator is illuminated, wait for about 2 minutes,
there will be coffee flowing out.
7. After desired coffee has obtained, you should turn steam knob to (Fig. 2/2) position, the indicator go out
and the coffee maker stops working, your coffee is ready now. Then remove the carafe and turn the steam
control knob to (Fig. 2/3) position release the residual steam in the tank.
WARNING: Do not leave the coffee maker unattended during making the coffee, as you need operate
manually sometimes!
8. Before removing steel mesh or opening the tank cover, make sure the pressure in the tank shall be
released. The method is turn the steam knob to the (Fig. 2/3) position firstly, the steam in the tank will eject
from the frothing device. After pressure has released, and wait for the steel mesh cooling down, you can
remove the steel mesh or open the tank cover.
9. After finishing making the coffee, you can take the metal funnel out through turn clockwise, and then pour
the coffee residue out with the steel mesh pressed by press bar. Let them cool down completely, then rinse
(see picture 1)
9. Boiler
10. Reservoir platre
11. Base
3