Controls Description; Grass Cutting - ST MCS 474 Serie Manual De Instrucciones

Ocultar thumbs Ver también para MCS 474 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 42
OPERATING INSTRUCTIONS
For information on the engine and the battery (if sup-
plied), read the relevant owner manuals.
NOTE – The number which precedes each paragraph
links the references in the text to the respective illus-
trations (listed on page iii and following pages).
1. COMPLETE ASSEMBLY
NOTE The machine can be supplied with some parts al-
ready assembled.
WARNING!
Unpacking and completing the assem-
bly should be done on a flat and stable surface, with
enough space for moving the machine and its packag-
ing, always making use of suitable equipment.
Disposal of the packaging should be done in accord-
ance with the local regulations in force.
1.1 Assembling the handle
• Model 474:
i -   A ssemble one of the ends of the lower part of the han-
dle  (1)  using  one  of  the  two  lower  knobs  and  relative 
screws  (2),  previously  removed  from  their  respec-
tive holes.
ii -   S crew  on  the  knob  (2)  to  about  half-way  along  the 
screw thread.
iii -   A ssemble the other end of the lower part of the han-
dle (1) and lock into position using the second lower 
knob (2) and relative screws.
iv -   F ully tighten the two knobs (2).
• Model 504:
      –     A ssemble the lower part of the handle (1) and secure 
in place using the lower knobs (2), previously removed 
from their respective holes.
Assemble  the  top  part  (3)  using  the  knobs  (4)  and  sup-
plied screws. 
Fit  the  cable  fasteners  (5)  as  shown  and  secure  the  con-
trol cables.
• Manual ignition models
• Electric key ignition models
      F it  the  starter  cable  in  the  guide  spiral  (6)  and  tighten 
the nut (7).
1.2 Battery connection
• Electric key ignition models
      C onnect the battery cable to the general wiring connec-
tor on the lawnmower.
• Electric push-button ignition models
      I nsert the supplied battery in the relative engine compart-
ment (par. 3.2b, "II - "III").

2. CONTROLS DESCRIPTION

NOTE The meanings of the symbols on controls are ex-
plained in the previous pages.
2.1 Throttle lever
The throttle is controlled by the lever (1).
Lever positions are indicated on the relevant plate.
Some models have a fixed speed engine with no need for 
a throttle.
2.2 Engine brake lever / cutting means
The cutting means brake is controlled by the lever (1) which 
must be held against the handle during ignition and during 
lawnmower operations. 
The engine stops when the lever is released. 
2.3 Drive lever (where applicable)
On power-driven models, push the lever (1) toward the han-
dle for forward movement.
The  lawnmower  stops  moving  forward  when  the  lever  is 
released. 
The  engine  must  always  be  ignited  with  the  drive  disen-
gaged.
WARNING!
sion, do not pull the machine backwards with the trans-
mission engaged.
2.4 Converter control lever (if fitted)
In the models with drive systems, the converter control le-
ver  (if  fitted)  allows  the  operator  to  regulate  forward  gear 
speed.
To  do  so,  move  the  lever  (1)  following  the  indications  pro-
vided near the control lever.
IMPORTANT The engine must be running and the drive
engaged when switching from one speed to another.
Do not touch the converter control when the engine is
stopped. Doing this could damage the converter.
NOTE If the machine does not move forward with the le-
ver in the «
» position, simply move the lever to «
then immediately return to the «
2.5 Cutting height adjustment
The cutting height is adjusted by the levers (1). 
The four wheels must be adjusted to the same height. 
DO THIS WHEN THE CUTTING MEANS IS STATIONARY.

3. GRASS CUTTING

3.1a Preparation for mowing and mulching
–  On  models  with  a  side  discharge:  make  sure  that  the 
side discharge guard (2) is lowered and blocked by the 
safety lever (1).
3.1b Preparation for mowing and side discharge
of grass (if provided)
–    P ush  the  safety  lever  (1)  slightly  and  lift  the  side  dis-
charge guard (2).
–    I nsert the side discharge chute (3) as shown in the figure.
–    C lose the side discharge guard (2) so that the side dis-
charge chute (3) is locked in place.
To remove the side discharge chute:
–    P ush  the  safety  lever  (1)  slightly  and  lift  the  side  dis-
charge guard (2).
–    R elease the side discharge chute (3).
3.2 Engine ignition
During  ignition,  follow  the  instructions  in  the  engine  man-
ual.
3.2a
• Manual ignition models ("I")
Pull  the  cutting  means  brake  lever  (1)  against  the  handle 
and firmly tug the knob on the ignition cable (2). 
EN - 4
To prevent damage to the transmis-
» position.
» and

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mcs 504 serie

Tabla de contenido