Preparing For Use; Using The Toilet - Thetford C-250 Manual Del Usuario

GB
Instructions for use
INTRODUCTION
The Thetford Cassette Toilet is a high quality product. The
toilet forms an integral part of your caravan or camper
bathroom, thanks to its functional design which combines
modern styling and ease of use. The C-250 Cassette Toilet
is manufactured from high quality synthetic materials which
makes it a durable, user and maintenance friendly toilet.
The toilet is made up of two parts: a permanently fixed part
and a waste-holding tank that is accessible from the outside.
The removable waste-holding tank is located under the
toilet bowl and can be removed via a door on the outside of
the caravan or camper. The Thetford Cassette Toilet is the
solution to the sanitary problem in your caravan or camper!
The operating instructions in this owner's manual cover
Thetford Cassette Toilet models C-250S, C-250CS (models
connected to the vehicle's central water tank) and C-250CWE
(model with its own flush-water tank). There are differences
in the use of these models. Please ensure that you follow the
instructions that apply to your toilet model.
PARTS
a) Removable seat and cover
b) Swivelling toilet bowl
c) Blade handle
d) Flush button
e) Waste-holding tank level indicator
f) Water filling door (only if toilet has own flush-water tank)
g) Rotating emptying spout
h) Automatic pressure release vent
i) Sliding cover
j) Removable mechanism
k) Vent plunger
l) Pull-out handle
m) Wheels
n) Blade opener
o) Access door to waste-holding tank
Additional Features
p) Electric blade opener
q) Electric Ventilator
r) Waste Pump-Out system
s) Waste-holding tank multi-level indicator
t) Flush-water tank level indicator (only if toilet has its own
flush-water tank)
Note. Some additional features can be bought at Thetford
dealerships.

PREPARING FOR USE

1. Open the access door on the outside of your caravan or
camper.
2. Remove the waste-holding tank by pulling the safety
catch (which holds the tank in place) upwards.
3. Pull the waste-holding tank outward. Tip it slightly and
take the tank fully out.
4. Place the tank upright and turn the rotating emptying
5. Remove the cap, with the measuring cup inside, from
6. Slide the waste-holding tank back into its original
7. For toilets with own flush-water tank: Open the water
Preparing for use with Additional Features
8. Electric Ventilator: Open the access door on the outside
9. Remove the filter housing cover and if no filter is

USING THE TOILET

10. Turn the bowl to the desired position with the cover
11. To activate the control panel, press the flush-button
(standard)
12. After use, open the valve blade (if still closed) by turning
- 3 -
spout upwards.
the emptying spout and pour the correct dosage of
Thetford toilet fluid (see product label) into the waste-
holding tank. This avoids unpleasant smells and keeps
the inside of the tank clean. Next add approximately 2
litres of water - enough to ensure that the bottom of the
waste-holding tank is covered. For more information on
Thetford toilet fluids, see last page of this manual. Screw
the cap back onto the emptying spout and turn back to
its original position.
Note. The emptying spout measuring cap is supplied in
the same packaging as this manual.
Warning! Never add toilet fluid directly via the blade
or the toilet bowl as this could damage the lip seal of
the waste-holding tank. Always pour the fluids via the
emptying spout.
position via the access door.
Make sure that it is secured with the safety catch. Close
the access door and lock it. Your Thetford toilet is now
ready to use.
Warning! Never use force if you cannot get the tank
back into place easily. This may cause serious damage.
If blockage occurs, always check if the blade handle is in
the correct (closed) position.
filling door and fill the flush-water tank with the correct
dosage of Aqua Rinse. This Thetford toilet fluid keeps the
flush water fresh and improves the flushing. Next, fill up
the flush-water tank with clean water (approximately 8
litres) using a jerry can or hose. Close the door and lock
it. Your toilet is now ready to use.
Note. Use fresh (tap) water for the water tank.
of your caravan and remove the waste-holding tank (as
described above).
present, peel off the sticker lids on the filter and place
the new filter into the filter housing. Place back the cover
of the filter housing.
Note. Clearly read the instructions on the filter on how to
place the filter in the filter housing
(standard)
closed and using both hands.
once. The control panel display will stay activated for
approximately 5 minutes. Run water into the bowl by
pressing the flush knob briefly or open the valve blade by
turning thehandle anti-clockwise. Your Thetford
toilet is now ready for use.
the handle anti-clockwise. Flush the toilet by pressing
the flush knob for several seconds. TIP! The flush of
your toilet will be more effective if you pulsate the flush
GB