Publicidad
Idiomas disponibles
Idiomas disponibles
14.
42. Press and release the "RESET" button. In this case, the
green indicator light should light up. (Fig. R)
43. If, during cutting, the machine reaches load level
close to the overload level, the PRCD device will be
triggered and will stop the cutter. If this happens,
release the on/off switch and set the machine to its
highest position (outside of the cutting zone) and wait
for at least 3 seconds before continuing.
Proper position of the hands:
WARNING! To reduce the risk of serious personal
injury, hold the machine with both hands at all times
to prevent any sudden movements from it.
Square cut
44. To make square cuts, position yourself behind the
machine. Put one hand on the main handle and slide
the cutter in the guide. For greater comfort, place the
other hand on the suction intake cover. This provides
better balance and sliding of the cutter.
Mitred cut
45. For mitred cuts, position yourself parallel to the blade.
Place your right hand on the main handle and the left
hand on the secondary handle.
Square and 45º angle cuts:
46. The cutter has a mark for the square cut and another
for 45°, as shown in the image. (Fig. S)
47. There is also a reference measurement to facilitate the
positioning of the guide (30mm).
48. These indicate the blade position during the cutting
operation in different situations: 0º and 45º.
N.B.: the system should used with standard blades,
NOT reinforced blades. Depending on the case, the
position of the cutter will need to be adjusted based
on the blade.
Connection:
49. For safety reasons, the on/off switch of the tool is
equipped with a safety button to prevent the machine
from turning on unexpectedly.
50. To start the cutter, press the safety button on the top
of the switch. The on/off switch will now be free to
start up the tool.
WARNING! To reduce the risk of serious personal
injury, support the work piece correctly, as shown,
and hold the cutter firmly to avoid losing control and
prevent potential kickback.
51. Keep your hands and the power cord away from the
cutting zone to prevent it from being snagged or
tangled on the piece being cut.
52. Put the machine in the proper position on the guide
profile.
53. Adjust the depth and cutting angle of the machine.
54. When the blade is not yet in contact with the piece
to be cut, press the safety button and then the on/
off switch, allowing the machine to reach its maximum
speed.
55. Holding the machine firmly in both hands, push it
forward slowly until the blade comes into contact with
the piece being cut and advance until the desired cut
has been completed.
WARNING! Do not apply pressure on the machine
during the cutting operation; the machine should slide
smoothly on the guide profile.
Disconnection:
56. Release the on/off switch to turn the machine off.
57. The cutter will continue to rotate for a few moments
after it has been turned off; wait until the machine
is completely stopped before removing it from the
English
TRANSLATION OF THE ORIGINAL
58. Remember that the cutter must be unplugged from
3.3 Cleaning and maintenace
WARNING! Unplug the machine before carrying out any
adjustments, repairs or maintenance.
Proper cleaning and maintenance of the machine can
extend its lifetime.
59. Do not submerge the machine in water.
60. Keep the ventilation slots clean and open to guarantee
61. For optimum cleaning, wipe the machine with a damp
62. Examine the machine's cords periodically and if they
63. Keep handles dry and clean and free of grease and oil.
64. We recommend cleaning the rolling tracks of the
65. The cutter comes with a second set of brushes. Check
Adjustment of the depth lever:
66. The depth-adjustment lever is adjusted at the factory.
67. Put the cutter in its lowest position and remove
68. Release the lever and turn the grooved shaft until it
69. Mount the lever oriented at approximately 45° and
70. Check that the lever locks the head position and that
Adjustment of the mitre lever:
71. The lever for mitred cuts is installed and adjusted at
72. Put the cutter in its lowest position and remove the
73. Tilt the head at a 45° angle and tighten the hexagonal
74. Once
75. Insert the locking washer into the slot of the hexagonal
76. Verify that when the lever is in the mitre cutting
cutting position.
the power installation when moving from one work
zone to another and when carrying out adjustment
and maintenance operations.
sufficient cooling. Blocked ventilation slots can
damage the machine.
cotton cloth. In all cases, avoid the use of solvents
and certain types of cleaning agents with this type of
components.
are damaged, have them repaired by an authorised
technical service.
guide with a cotton cloth dampened with water. Do
not lubricate the guides with oil. (Fig. T)
the brushes for wear and, if necessary, replace them
with new ones as described below:
- Unplug the machine from the installation and wait
for the blade to stop completely.
- Remove the brush-holder plugs with a flat-head
screwdriver (turning counter-clockwise, tool not
included) and replace the brushes.
- Make sure that they are properly aligned and can
slide freely.
If the lever does not lock the cutter head, carry out the
following steps:
the screw indicated in the image (turning counter-
clockwise).
stops. (Fig. U)
secure the retaining screw (clockwise).
the lever is it approximately 30º (see image). (Fig. V)
the factory. If the lever does not lock the cutter head,
carry out the following steps:
locking washer that releases the lever and remove it.
nut until the system is locked (clockwise).
again,
position
approximately as shown in the image.
nut and verify that the system works correctly. If not,
repeat the operation. (Fig. W)
position that there is no interference with the side
guard.
the
adjustment
lever
Publicidad
