Wayne WLS76 Instrucciones De Funcionamiento Y Manual De Piezas página 3

Operating Instructions and Parts Manual
Electrical Connections
(Continued)
pump in accordance with the National
Electrical code and all applicable local
electrical codes.
The motor must be grounded by
connecting a copper conductor to the
grounding screw provided within the
wiring compartment.
The voltage of power supply must match
the voltage of the pump. The WLS75,
WLS100 and WLS150 have dual voltage
motors preset at the factory to 230 volts.
The motors can be converted to 115 volts
by turning the voltage selector to the
desired voltage (See Figure 5). Use a
needle nose pliers to pull the selector out
approximately 1/4", rotate and then
reinsert in correct position. The WLS200
cannot be converted; the motor is
230 volts only.
230 V
115 V
115 V
Figure 5 - Voltage Selector
3/4 HP Pump Capacity in
Lift
GPH Operating Pressure (psi)
in
Feet 10
5 3900 3320
10 3780 3120
15 3600 2910
20 3250 2670
25 3010 2560
1 HP Pump Capacity in GPH
Lift
Operating Pressure (psi)
in
Feet 10
5 4410 3920
10 4180 3520
15 3830 3340
20 3680 3060
25 3340 2720
CONNECTING WIRES
Terminal cover must be in place for safe
operation. Ground in accordance with local
and national electrical codes. Keep fingers
and objects away from openings and
rotating parts. Disconnect power sources
before touching internal parts. See figure 6
for appropriate wiring locations.
Figure 6 - Connecting Wire
Operation
pump without water may cause seal
damage. Fill the pump with water
before starting.
PRIMING THE PUMP
After pump installation is complete, the
pump must be primed. Remove the
pipe plug in the discharge piping and
230 V
fill the pump and suction pipe with
clean water. Turn power to pump on. If
the pump does not pump water in 10
minutes, turn off the pump and refill
with clean water.
Lift
GPH Operating Pressure (psi)
in
20 30 Feet
2320 5
2100 10
1190 15
990 20
840 25
Lift
in
20 30 Feet
2570 5
2300 10
1780 15
1160 20
1260 25
Ground Screw
Ungrounded
Line (L1)
Terminal
Board (L2)
Never run the
pump dry. Running
1-1/2 HP Pump Capacity in
10 20 30
4790 4480 3480 2060
4610 4310 3190 1520
4320 4040 2900
3900 3720 2680
3810 3300 2390
2 HP Pump Capacity in GPH
Operating Pressure (psi)
10 20 30
5980 5560 4310 3060
5410 5220 4090 2880
5230 4980 3900 2570
4120 3840 3510 2210
3980 3600 3300
3
WLS150, WLS200
If the pump does not operate after
repeated attempts, check the following:
1. Vertical distance of pump to water
level must not be over 25 feet.
2. Suction piping must be air tight.
3. Be sure valve(s) are open if used in
discharge or suction piping.
or clogged discharge. The water inside
the pump could boil and damage the
pump.
Maintenance
Maintain adequate ventilation for the
pump motor. The motor bearings are
permanently lubricated at the factory.
Additional lubrication is not required.
DRAINING FOR WINTER
Always protect pump and piping
against freezing temperatures. If there
is any danger of freezing, drain the
system. To drain the system:
1. Remove the pipe plug from the
discharge tee.
2. Remove the 1/4" plug from the
lower front face of the pump.
3. Drain all piping below the frost line.
40
0
0
0
40
0
www.waynepumps.com
WLS75, WLS100
Never run the
pump with a closed