Common Operations - Yamaha NX-U10 Manual De Instrucciones

Installation of USB drivers
The installation procedure is variable depending on OS. After
"Common operations" below, follow the installation procedure for
your OS.
• You may need the CD-ROM of the OS running on your computer
to install the device drivers. For details, refer to the manuals of your
computer.
• The following installation procedures for the device driver
installation method may not be applicable to certain PC
environments. In this case, follow the instructions given in the
displayed dialog boxes. Consult the PC manufacturer or your
computer dealer in case of doubt.
• When you change the connecting USB port to another one, it may
be required to reinstall the USB driver.
• The displayed messages etc. may vary depending on your computer
or OS.
• When installing USB drivers into an OS other than the ones
mentioned below, refer to the manuals of your computer.

Common operations

1
Switch on your computer to boot the OS.
2
Connect this unit to your computer.
For the connection method, see steps 1 to 4 in "1 When
using USB bus power" on page 2.
Installing on Windows Vista, Windows XP,
Windows 2000 or Mac OS*
Press POWER to switch on this unit.
Your computer detects this unit and installs the necessary
devices automatically.
This unit gets ready for use after completion of the installation.
* (Mac OS 9.1 or later, Mac OS X 10.0 or later)
Installing on Windows Me
1
Press POWER to switch on this unit.
2
Install the USB-Compatible Device.
Your computer automatically detects the "USB-Compatible
Device" and installs it.
3
Install the USB Audio Device.
[
Add New Hardware Wizard
Window: [Windows has found the following new hardware]
Check "USB Audio Device" is displayed
Window: When [Digital signature confirmation] is
displayed
Check "USB Audio Device" is displayed
Select [Yes]
Click [OK]
Select "Automatic search for a better driver. [Recommended]"
Click [Next]
Your computer automatically detects the "USB Audio
Device" and installs it.
Check "Windows has finished installing the software for
the new hardware device" is displayed
Click [Finish]
4
Install the USB Human Interface Device.
Your computer automatically detects the "USB Human
Interface Device" and installs it.
This unit gets ready for use after completion of the
installation.
] is displayed
Installing on Windows 98SE
1
Press POWER to switch on this unit.
[Add New Hardware Wizard] is displayed
2
Install the USB-Compatible Device.
Window: [This wizard searches for new drivers for]
Check "USB-Compatible Device" is displayed
Click [Next]
Select "Search for the best driver for your device.
[Recommended]"
Click [Next]
Select "CD-ROM Drive"
*At this time, leave the items checked by default.
Click [Next]
Window: When [Add New Hardware Wizard] is displayed
Select "The updated driver [Recommended]"
Click [Next]
Window: [Windows driver file search for the device]
Check "USB-Compatible Device" is displayed
Click [Next]
Check "Windows has finished installing the software
that your new hardware device requires." is displayed
Click [Finish]
3
Install the USB Human Interface Device.
Window: [This wizard searches for new drivers for]
Check "USB Human Interface Device" is displayed
Click [Next]
Select "Search for the best driver for your device.
[Recommended]"
Click [Next]
Select "CD-ROM Drive"
*At this time, leave the items checked by default.
Click [Next]
Window: [Windows driver file search for the device]
Check "USB Human Interface Device" is displayed
Click [Next]
Check "Windows has finished installing the software
that your new hardware device requires." is displayed
Click [Finish]
4
Install the USB Audio Device.
Window: [This wizard searches for new drivers for]
Check "USB Audio Device" is displayed
Click [Next]
Select "Search for the best driver for your device.
[Recommended]"
Click [Next]
Select "CD-ROM Drive"
*At this time, leave the items checked by default.
Click [Next]
Window: [Windows driver file search for the device]
Check "USB Audio Device" is displayed
Click [Next]
Check "Windows has finished installing the software
that your new hardware device requires." is displayed
Click [Finish]
This unit gets ready for use after completion of the
installation.
3
En