DeWalt DWE4056 Traducido De Las Instrucciones Originales página 45

NOTE: If, after a period of time the closed (Type 1)
guard becomes loose, tighten the adjusting screw
with the clamp lever in the closed position.
CAUTION: If the guard cannot be
tightened by the adjusting screw, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to authorized repair agent to repair or
replace the guard.
NOTICE: Do not tighten adjusting
screw with clamp lever in open position.
Undetectable damage to guard or
mounting hub may result.
Fitting and Removing a Grinding or
Cutting Disc (fig. 1, 4, 5)
WARNING: Do not use a damaged
disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange (D) correctly onto the
spindle (B) (fig. 4).
3. Place the disc (P) on the backing flange (D).
When fitting a disc with a raised centre, make
sure that the raised centre (O) is facing the
backing flange (D).
4. Screw the threaded clamp nut (E) onto the
spindle (B) (fig. 5):
a. The ring on the threaded clamp nut (E) must
face towards the disc when fitting a grinding
disc (fig. 5A);
b. The ring on the threaded clamp nut (E)
must face away from the disc when fitting a
cutting disc (fig. 5B).
5. Press the spindle lock button (A) and rotate the
spindle (B) until it locks in position.
6. Tighten the threaded clamp nut (E) with the hex
key provided or a two pin spanner.
7. Release the spindle lock.
8. To remove the disc, loosen the threaded clamp
nut (E) with the hex key provided or a two pin
spanner.
NOTE: Edge grinding can be performed with
Type 27 wheels designed and specified for this
purpose; 6 mm thick wheels are designed for
surface grinding while 3 mm wheels are designed
for edge grinding. Cutting can be performed by
using a cutting wheel and a Type 1 guard.
Mounting Wire Brushes
and Wire Wheels
Wire cup brushes or wire wheels screw directly
on the grinder spindle without the use of flanges.
Use only wire brushes or wheels provided with a
M14 threaded hub. A Type 27 guard is required
when using wire brushes and wheels.
CAUTION: Wear work gloves when
handling wire brushes and wheels.
They can become sharp.
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the
above procedure.
NOTICE: Failure to properly seat the
wheel hub before turning the tool on may
result in damage to tool or wheel.
Fitting and Removing a
Backing Pad/Sanding Sheet (fig. 1)
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (D).
3. Place the rubber backing pad correctly onto the
spindle (B).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (E) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (A) and rotate the
spindle (B) until it locks in position.
7. Tighten the threaded clamp nut (E) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (E) with the hex key
provided or a two pin spanner.
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
english
43