Initial Settings; Autoscan - Sylvania 6842THG Manual Del Propietário

Ocultar thumbs Ver también para 6842THG:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

I
NITIAL SETTINGS
Hint: Before starting initial setup you must connect antenna.

INITIAL SETTINGS

This section describes the initial settings when you
first turn on the power after purchase. The initial
setting items are shown below.
• LANGUAGE SELECTION
You can select the menu language displayed on
the screen among English, Spanish and French.
• AUTOSCAN (TV/DTV)
(Select "Air" when using antenna)
The channels broadcasted in TV and DTV are
automatically scanned and memorized. Only the
receivable channels in the area where this TV is
used will be memorized.
• AUTOSCAN (CATV)
(Select "Cable" when using RF/Incoming cable)
The channels broadcasted in CATV are automati-
cally scanned and memorized.
POWER
POWER
1
2
4
5
7
8
-
0
SETUP
BACK
1
After making all the necessary connections, turn
on this TV.
2
Press [POWER]. Initial Setup menu will appear.
• This operation may take a few moments.
• If Initial Setup menu does not appear press
and hold [ENTER] for 3 seconds, initial setup
will appear then proceed to step 3. If you have
already turned on this TV before, refer to
"LANGUAGE SELECTION" on page 17 to
select a language for the on-screen displays.
3
Select your language using [ K / L ], press
[ENTER].
When you first turn on the power, the following
screen is displayed.
Initial Setup
Initial Setup
Select the language used for setup.
Elija idioma de preparación.
Sélectionner langue écran config.
Select
ENTER
The Antenna Confirmation will be displayed in
the selected language after you press [ENTER].
INPUT
SLEEP
SELECT
3
6
AUDIO
9
STILL
SCREEN
MODE
ENTER
ENTER
INFO
English
Español
Français
SETUP
Enter
Exit
4
Select destination of ANT IN jack using [ K / L ],
press [ENTER].
Initial Setup
Initial Setup
Make sure the antenna is connected to "ANT. IN" jack.
Select the destination of "ANT. IN" jack.
Air
Cable
Or
Select
Enter
ENTER
5
Autoscan will start automatically.
Initial Setup
Initial Setup
Now the system is scanning for channels,please wait.
5%
Analog channels
Digital channels
• When scanning is completed, the smallest
memorized channel will be displayed.
NOTES:
• If you do not operate this TV for more than 45 seconds
while initial setup, the message boxes start to move to the
lower left-hand corner of the screen. This is for saving you
screen from burn-in. Press any key except [POWER] to can-
cel it.
• The initial Autoscan function can be executed for either "Air"
or "Cable" only once. When you change the connection
(Air/Cable), set the "Autoscan" again. (Refer to page 14.)
• If you connect cable system directly, contact the CATV
installer.
• When the scanning is not completed, Helpful Hint will be
displayed every time you turn on the power. If you have
previously registered channels when this screen appears
you can select a channel with number buttons.
No channel is registered.
Press and hold "ENTER" key for 3 seconds.
Contact support hotline provided on manual or back of unit.
Sin canal registrado.
Mantenga oprimida la tecla "ENTER" durante 3 segundos.
Llame teléfono de apoyo en manual o atrás de TV.
Pas de chaîne consign.
Maintenir la touche "ENTER" pressée 3 secondes.
Contacter numero d'urgence dans manuel ou arrière appareil.
• Support hotline is provided on the front page of this
manual.
Air
Cable
ANT IN
BACK
SETUP
Back
Exit
1ch
0ch
SETUP
Exit
2-0
13
EN

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido