Environmental Protection; General Safety Instructions - Silverline 245115 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 17
GB

Environmental Protection

Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Read instruction Manual.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Double insulated for additional protection.
Conforms to relevant legislation and safety standards.
Specification
Voltage .................................................230-240V~
Frequency ............................................50Hz
Power ...................................................1050W
No load speed ......................................0-1000/0-3000min
Max drilling capacity
- Concrete ........................................20mm
- Wood .............................................30mm
- Steel ..............................................13mm
Weighted vibration ...............................2.2m/s
Uncertainty ..........................................1.5m/s²
Sound pressure ....................................95.2dB(A)
Sound power ........................................108.2dB(A)
Uncertainty ..........................................3dB(A)
Protection class ....................................
The sound intensity level for the operator may exceed
85dB(A) and sound protection measures are necessary.
As part of our ongoing product development, specifications
of Silverline products may alter without notice

General Safety Instructions

Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.
Remove adjusting keys
Always check to see that keys and adjusting devices are removed
from the tool before use.
Clean the work area
• Accidents can occur where benches and work areas are cluttered or
dirty, floors must be kept clear, avoid working where the floor is slippery.
If working outdoors, make yourself aware of all potential slip and trip
hazards before using this tool.
Children and pets
• Children and pets should always be kept at a safe distance from your
work area. Lock tools away where children can't get access to them.
Do not allow children, or untrained persons to use this tool.
4
245115_Instructions NEW.indd 4
Use the correct tool
• Don't force, or attempt to use a tool for a purpose it was not designed for.
Wear suitable clothing and footwear
• Don't wear loose fitting clothing, neckties, jewellery, or other items which
may become caught. Wear non slip footwear, or footwear with protective
toe caps where appropriate. Long hair should be covered or tied back.
Keep your balance
• Don't over reach, keep proper footing at all times, do not use tools
when standing on an unstable surface.
Accessories
• The use of any attachment or accessory other than those mentioned
in this manual could result in damage or injury. The use of improper
accessories could be dangerous, and will invalidate your guarantee.
Secure work
• Always ensure work is secure. If appropriate use a clamp or vice.
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing,
check carefully that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or other
part that is damaged should be immediately repaired or replaced by an
authorised service centre. Do not use if defective.
Mains Electrical Tool Safety
-1
GREEN/YELLOW
OR GREEN
2
BLUE
(Neutral)
• The wires in this product are coloured:
Blue
Brown
Green & Yellow
• As the colours may not correspond with the coloured markings in your
plug, proceed as follows.
• The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black, the wire which
is coloured brown must be connected to the terminal which is marked
L or coloured red.
• This appliance must be protected by a suitable fuse.
• To prevent fire or shock hazard, do not expose this product to rain/
water or moisture.
• There are no user serviceable parts inside except those referred to
in this manual. Always refer servicing to qualified service personnel.
Never remove any part of the casing unless qualified to do so; this
unit contains dangerous voltages.
• Use of a residual current device (RCD) will reduce the risk of
electric shock.
NEVER CONNECT THE BROWN OR BLUE WIRE TO THE EARTH PIN OF THE
13 AMP PLUG. IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN
Dangerous environment
• Do not use power tools in damp or wet conditions, or expose them
to rain. Provide adequate surrounding work space and keep area well
lit. Do not use power tools where there is a risk of explosion or fire from
Earthed
Double Insulated
FUSE
BROWN
BLUE
(Live)
(Neutral)
Neutral (N)
Live (L)
Earth (E)
FUSE
BROWN
(Live)
4/3/10 10:18:40

Publicidad

Tabla de contenido
loading

Tabla de contenido