Tabla De Contenido; Handling; Type Designation; Pump Key For Cr, Cri, Crn 1S, 1, 3, 5, 10, 15 And - Grundfos CR Serie Instrucciones De Instalación Y Funcionamiento

Tabla de contenido

Publicidad

CONTENTS
1.
2.
2.1
2.2
Pump key for CR, CRN 32, 45, 64 and 90
3.
4.
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
5.
6.
6.1
7.
8.
9.
10.
10.1
11.
12.
Before beginning installation procedures, these in-
stallation and operating instructions should be stud-
ied carefully. The installation and operation should
also be in accordance with local regulations and ac-
cepted codes of good practice.

1. Handling

The motors of the CR, CRI, CRN 1s, 1, 3, 5, 10, 15
and 20 pumps are supplied with lifting eyes which
must not be used for lifting the entire pump.
When the entire pump is to be lifted, observe the following:
CR, CRI, CRN 1s, 1, 3, 5, 10, 15 and 20 pumps fitted with
Grundfos MG motors should be lifted in the pump head by
means of straps or the like.
CR, CRN 32, 45, 64 and 90 fitted with Grundfos MG motors up
to and including 11 kW should be lifted by means of the eye
nut fitted to the pump head.
CR, CRN 32, 45, 64 and 90 fitted with Siemens motors of
15 kW and up should be lifted by means of the eye bolts fitted
to the motor flange.
For other motor makes than those mentioned above, it is rec-
ommended to lift the pump in the pump head by means of
straps.
14

2. Type designation

Page

2.1 Pump key for CR, CRI, CRN 1s, 1, 3, 5, 10, 15 and

14
20
14
Example
14
Pump range: CR, CRI, CRN
14
Nominal flow rate in m³/h
15
Number of impellers
15
Code for pump version
15
Code for pipework connection
15
Code for materials
15
Code for rubber pump parts
15
15
Code for shaft seal
15
2.2 Pump key for CR, CRN 32, 45, 64 and 90
15
16
Example
16
16
Pump range: CR, CRN
16
Nominal flow rate in m³/h
16
Number of stages
17
Number of impellers with reduced
17
diameter
17
Code for pump version
17
Code for pipework connection
17
Code for materials
18
Code for rubber pump parts
18
Code for shaft seal

3. Applications

Grundfos multistage in-line centrifugal pumps, types CR, CRI and
CRN, are designed for a wide range of applications.
Pumped liquids
Thin, non-explosive liquids, not containing solid particles or fi-
bres. The liquid must not attack the pump materials chemically.
When pumping liquids with a density and/or viscosity higher than
that of water, motors with correspondingly higher outputs must be
used, if required.
CR, CRI, CRN
For liquid transfer, circulation and pressure boosting of cold or
hot clean liquids.
CRN
In systems where all parts in contact with the liquid must be made
of high-grade stainless steel, CRN pumps must be used.
CR 3- 10 X - X - X - X - XXXX
CR 32- 2- 1 - X - X - X - X - XXXX

Publicidad

Tabla de contenido
loading

Tabla de contenido