Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Inner Bumper
Structure
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24785F
Wrenches: 11/16
Drill Bits: N/A
7/16 Pull Wire
Sealant
1
2
j
Qty. (2)
Carriage Bolt 7/16-14 x 1.50 Gr.5
k
Qty. (4)
Spacer ¼ x 1 x 3
l
Qty. (4)
Conical Toothed Washer 7/16
1.
Remove spare tire.
2.
Remove the two rubber plugs from bottom of trunk pan/spare tire well and return to vehicle owner.
3.
Install carriage bolts and spacers (Items 1 & 2) through inner bumper structure with pull wire, carefully pulling
fastener through existing holes in bumper.
4.
Install carriage bolts and spacers (Items 5 & 2) through holes in trunk pan.
5.
Raise hitch into position over carriage bolts and install conical toothed washers and hex nuts onto carriage
bolts. Tighten all fasteners to specified torque.
6.
Seal holes in trunk pan to prevent intrusion of exhaust fumes or water.
7.
Replace spare tire.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2015 Cequent Performance Products, Inc. – Printed in Mexico
Installation Instructions
MAZDA 6 WAGON
Fascia
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
5
2
Trunk Pan – Spare
Tire Well
3
4
Tighten all 7/16-14 GR5 fasteners to 50 lb.-ft. (68 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (907 Kg.) Max Gross Trailer Weight
200 LB (91 Kg.) Max Tongue Weight
Wiring Access Location: PC3 & 4
m
Qty. (4)
Nut 7/16-14
n
Qty. (2)
Carriage Bolt 7/16-14 x 1.75 Gr.5
Sheet 1 of 3
24785N
Part Numbers:
24785
77159
60857
Existing Holes in
Inner Bumper Structure
3
4
10-13-15
Rev. B
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Performance Products 24785
Resumen de contenidos para Cequent Performance Products 24785
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2006, 2015 Cequent Performance Products, Inc. – Printed in Mexico Sheet 1 of 3...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systè mes d’attelage. 2006, 2015 Cequent Performance Products, Inc. - Imprimé au Mexique...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684 Hoja 3 de 3 24785N 10-13-15 Rev. B 2006， 2015 Cequent Performance Products, Inc. - Impreso en México Form F206 Rev A 5605...