Technical Data - AEG OMNI 18C-PB Manual Original

APPROVAL
This application head is approved for use on the following
powerbases:
OMNI 18C-PB......................................................... 18 V-
OMNI 300-PB ................................................ 220-240 V ~

TECHNICAL DATA

OMNI-RAD
Production code.................................................4407 06...
...00001-99999
Drill opening range .............................................. 1-10 mm
Drilling capacity in steel .......................................... 10 mm
Drilling capacity in wood ......................................... 18 mm
Wood screws (without pre-drilling) ........................... 4 mm
No-load speed ................................................... 0-550 min
Torque..................................................................... 12 Nm
Weight according EPTA-Procedure 01/2014 ....... 0.79 kg
Vibration Information
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Vibration emission value a
h
Drilling in metal
OMNI 18C-PB .................................................. 2.0 m/s
OMNI 300-PB ............................................... < 2.5 m/s
Uncertainty K = ................................................ 1.5 m/s
Screwing
OMNI 18C-PB ............................................... < 2.5 m/s
OMNI 300-PB ............................................... < 2.5 m/s
Uncertainty K = ................................................ 1.5 m/s
For technical data and approvals of powerbases for use with
various application heads please refer to the operating
instructions of the used powerbase.
WARNING
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 62841 and may be used to compare one tool
with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly
maintained, the vibration emission may diff er. This may
signifi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may signifi cantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the eff ects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work
patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Safety instructions for all operations
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live" and could
give the operator an electric shock.
6 ENGLISH
Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed
rated of the drill bit. At higher speeds, the bit is likely to
bend if allowed to rotate freely without contacting the
workpiece, resulting the personal injury.
Always start drilling at low speed and with the bit tip in
contact with the workpiece. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting the personal injury.
Apply pressure only in direct line with the bit and do not
apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal injury.
-1
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Chips and splinters must not be removed while the machine
is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Use a dust absorption system
2
and wear a suitable dust protection mask. Remove
2
deposited dust thoroughly, e.g. with a vacuum cleaner.
2
Remove the battery pack before starting any work on the
machine.
2
Always disconnect the plug from the socket before carrying
2
out any work on the machine.
2
The product will restart automatically if stalled. Switch off the
product immediately if it stalls. Do not switch on the product
again while it is still stalled, as doing so could trigger a
sudden recoil with a high reactive force. Determine why the
product stalled and rectify this, paying heed to the safety
instructions.
SPECIFIED CONDITIONS OF USE
Combined with an AEG OMNIPRO powerbase the Right
Angle Drilling Head is designed for for drilling and screwing
in wood, metal and plastics.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-1:2018+A11:2019
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-11-20
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091
(as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-1:2018+A11:2019
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2020-11-20
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINTENANCE
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine
(OMNI 18C-PB).
Always disconnect the plug from the socket
before carrying out any work on the machine
(OMNI 300-PB).
Please read the instructions carefully before
starting the machine.
Do not dispose electric tools, batteries/
rechargeable batteries together with
household waste material.
Electric tools and batteries that have reached
the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark.
ENGLISH 7