Playing Back Computer Music; Updating The Firmware Of The Transmitter; Troubleshooting - Yamaha YSP-4300 Manual Del Usuario

Charging an iPod
You can charge the iPod by connecting the transmitter to your
computer using the supplied USB cable.
Also, you can enjoy iPod music via the YSP-4300/YSP-3300
while charging the iPod.
Notes
• Charging may not be possible depending on the USB power
supply capability of your computer.
• Data synchronization between the iPod and computer may start
automatically when they are connected. You cannot play back
iPod audio on the YSP-4300/YSP-3300 during data
synchronization. Wait until data synchronization is completed,
or cancel it as necessary.

Playing back computer music

1
Set the group ID of the transmitter (☞p. 4),
center unit, and subwoofer to C1, C2 or C3.
For details on setting the group ID of the center unit and
subwoofer, see "GROUP ID" and "Connecting the
wireless subwoofer" in the Owner's Manual.
2
Connect the transmitter to your computer
with the supplied USB cable.
The USB driver software will be automatically installed
on your computer (only the first time the transmitter is
connected to the computer).

Troubleshooting

Refer to the table below when the unit does not function properly.
If the problem you are experiencing is not listed below or if the instructions below do not help, contact the nearest authorized Yamaha
dealer or service center.
First, check the following:
1 The power cable of your Yamaha product is connected to an AC wall outlet securely.
2 The latest firmware is installed on the transmitter or your iPod.
Problem
A wireless connection
cannot be made. (The
green indicator is off.)
5
En
USB cable (supplied)
USB
USB cable
(supplied)
Cause
Your iPod is not connected to the transmitter firmly.
The battery of your iPod is low or run out.
The supplied USB cable is not connected to the
transmitter (or computer) firmly.
The USB driver software is not installed on your
computer because the computer (operating system) is
not supported by the transmitter.
3
Start playback on your computer.
After a wireless connection between the transmitter and
YSP-4300/YSP-3300 is established, the YSP-4300/
YSP-3300 automatically selects the transmitter (YIT) as
the input source and starts to play the computer audio.
Notes
• The YIT-W12TX automatically stops if the YSP-4300/
YSP-3300 is turned off or if an input source other than "YIT" is
selected. To use the YIT-W12TX as a PC transmitter again,
disconnect the YIT-W12TX from the PC and then reconnect
them.
• If computer audio is not output from the YSP-4300/YSP-3300,
the transmitter may not be selected as the audio playback device
on your computer. Check the audio device settings on your
computer. For details, refer to the manuals of the computer.
• You cannot play back computer audio via the YSP-4300/
YSP-3300 when an iPod is connected to the transmitter.
• Do not use a USB hub when connecting the YIT-W12TX to a
PC.
y
Tips
• The YSP-4300/YSP-3300 automatically turns on if you start
playback on your computer.
• Some Yamaha products will terminate the wireless connection
and turn off automatically if a certain period of time elapses
after computer playback is stopped.
• You can enjoy videos on the computer monitor.

Updating the firmware of the transmitter

New firmware that provides additional features or product
improvements will be released as needed. Updates can be
downloaded from our website. Please check our website regularly
for Information.
Reconnect the iPod to the transmitter.
Charge the iPod (☞p. 5).
Reconnect the USB cable.
Use a computer (operating system) supported by the
transmitter (☞p. 6).
(Lights up green)
wireless connection
established
Remedy