Milwaukee WCE 65 Manual Original página 6

Loosen the Allen screw of the Spanntec-nut
Setting the
with the T-key (to stop).
cutting width
Move the outer diamond cutting disc to the
required cutting width.
Spanntec
To lock it in the required position fasten the
Allen screw tightly.
Set of distance 1. Loosen the screw and open and remove the
plates (special protective cover.
accessory)
2. Lock the work spindle by depressing the
spindle lock. Open the round nut of the upper
cutting disc with aid of a pin-type face span-
ner and remove it. Remove the upper cutting
disc.
3. Loosen the Allen screw with the T-key and
remove the Spanntec-nut.
4. Fit the diamond cutting disc to the collar of
the reduction ring and push it together with
the distance plates over the Spanntec-spin-
dle. The collar of the reduction ring must face
outside.
5. Screw down the Spanntec nut on the Span-
ntec-spindle and the round nut on the Span-
ntec-nut.
6. Fasten the Spanntec-nut with aid of the spanner (to steady depress the spindle
lock).
The number of the distance plates between the diamond cutting discs determines
the cutting width. Without distance plates (only with reduction ring) the cutting width
is 8 mm. The set of distance plates contains the following distance plates:
1 Spacing washer
2 Spacing washers
1 Spacing washer
Arrow on diamond cutting discs must agree with arrow on protective hood cover-
direction of rotation.
7. Reassemble the tool (see above).
Setting the
Loosen the wing nut and set the depth gauge
cutting depth to the required depth. Loosen the wing nut
and set the depth gauge to the required
depth.
The cutting depth gets less as the diamond
cutting discs wear down.
In order to prevent edges from the remaining
cut strip breaking out, set the cutting depth
slightly deeper.
10 ENGLISH
ENGLISH 8
Spanntec-
spindle
Spacing
washers
Reduction ring
Spanntec-nut
Round nut with drilled
holes in one face
1 mm
2 mm
3 mm
Advices for
operation
1. Pre-select the cutting depth and width.
2. Switch the machine on.
3. Position the machine to the wall with the
4. Cut the masonry groove by pulling the ma-
5. When you get to the end of the groove you
6. Put the machine down and break out the remaining strip with the paring-out tool.
Tips
WCE 65 ENGLISH 9
Only use the machine for dry cutting in stone.
Mind hidden electric lines, gas and water pipes. Check your working area, e.g. with
a metal detector.
back edge of the supporting table and plunge
in slowly until the supporting table is level
with the wall.
chine towards you (in direction of arrow in il-
lustration), guiding the machine with both
hands. Only cut straight lines radii are not
possible.
Always use the additional handle.
When cutting hard material, swing the ma-
chine slightly to and fro in the cut then the
diamond cutting discs stay sharper longer.
are cutting, lift the machine out first and then
switch off.
After switching off, the machine will not be
idle immediately. (After-running of the work
spindle.) Allow the machine to come to a stop before putting down.
The cutting discs get very hot when in use. Do not touch them before they have
cooled down.
To improve leading the machine with the parallel guide fix a wooden lath when cut-
ting horizontal/diagonal slots into walls.
Cutting hard materials, especially concrete, requires a very high engine perform-
ance. If the feed rate is too high the load-rate motor protection slows the motor
down.
We recommend the use of special cutting discs for cutting in concrete with a diam-
eter of 200 mm.
Blunt diamond cutting discs are recognisable by the large number of sparks that fly
during work, and can be resharpened by making a number of cuts in abrasive ma-
terial (e.g. plaster).
ENGLISH 11
WCE 65