Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLING A BATTERY/TOURNAMENT LOCK SWITCH CONT.
REMOVAL OF TOURNAMENT LOCK SWITCH
The RS Circuit Board (#ECB001) is equipped with a Tournament Lock Switch (#ELM003) that enables the user to
lock the firing mode of the marker. To lock the firing mode in Semi-Auto mode you must first turn the marker "ON"
and select Semi-Auto mode, which is the "Green" lower LED indicator. Removing the Tournament Lock Switch
at this point will lock the firing mode function in Semi-Auto mode. To disable the mode lock and access the Burst
mode re-install the Tournament Lock Switch onto the circuit board.
removed for easy reassembly.
WARNING
•
Spyder Electronic Markers are not water resistant.
•
Extreme moisture can cause serious damage to any Spyder Electronic Marker.
•
Always clean any dirt or paint inside the markers electronics.
•
Never attempt to modify the electronics circuitry, doing so will VOID all electronic warranties and liabilities
from Kingman.
BATTERY CHARGING
#JE1029
STEP 2 Connect the Spyder A/C Charger cord to the rear of the markers trigger frame.
STEP 3 The LED indicator on the A/C Charger will display RED when the battery is charging (US Model only).
STEP 4 The LED indicator on the A/C Charger will display GREEN when the battery is fully charged (US Model
only).
STEP 5 Unplug the Spyder A/C Charger cord from the rear of the markers trigger frame after charging.
STEP 6 Remove the Spyder A/C Charger from the power outlet.
NOTE:
It is recommended that the battery be charged prior to use in order to ensure maximum performance,
especially if the battery has not been used in over a week.
IMPORTANT:
You should never charge the battery over 24 hours or you can run the risk of damaging the battery or
electronics.
ELECTRONICS & SETTINGS
UPPER
LED LIGHT
LOWER
LED LIGHT
5
HELPFUL TIP:
Please note how the parts are
SPYDER LED A/C CHARGER
INSTRUCTIONS
To charge a Spyder 9.6 NiMH Battery the circuit board must be
in the OFF Position. Spyder Batteries (#JE1015 not pictured)
are not fully charged when purchased. Using the supplied
Spyder LED A/C 110v-120v Charger (#JE1029 US Model only)
or the Spyder Euro Charger A/C 220v-230v Charger (#JE1025)
Kingman recommends a charging time of 5 hours for a complete
charge.
STEP 1 Plug the Spyder A/C Charger into a power outlet.
UPPER
BUTTON
LOWER
BUTTON
CIRCUIT BOARD SETTINGS AND LED COLOR FUNCTIONS
EUROPEAN EDITION / SEMI MODE ONLY
POWER ON/OFF:
Pressing the Upper Button for 1 second will power the marker ON illuminating the LED lights
Red and Green. To Power OFF press and hold the Upper Button for 3-4 seconds, this shuts down the circuit board
and turns both LED lights off.
NOTE:
Once the circuit board is ON, it will automatically be set in Safe Mode.
SAFETY LIGHT ON/OFF:
When the circuit board has been turned ON, to release out of Safety press the Lower
Button for 1 second to turn OFF the Safety. Press the Lower Button for 1 second will activate Safe Mode ON.
NOTE:
The Eye Mode will automatically turn ON after you exit the Safe Mode.
EYE MODE ON/OFF:
When the circuit board has been turned ON press the Upper Button for 1 second to release
Eye Mode OFF. Press the Upper Button for 1 second to turn ON the Eyes.
NOTE:
When the Eye Mode is turned ON the trigger will not fire until there is a paintball in the breach.
HELPFUL TIP:
The Eye mode is able to turn ON when the marker is in 3 Burst.
MODES SEMI / 3 BURST:
Press and hold the Lower Button for about 3-4 seconds to change modes from Semi to
3 Burst. Press and hold the Lower Button for about 3-4 seconds to change back to Semi.
NOTE:
The Eye mode is able to turn ON when the marker is in 3 Burst Mode.
LED COLOR GUIDE
UPPER LED LIGHT in Red is Safe Mode ON.
UPPER LED LIGHT in Green is Eye Mode ON.
UPPER LED LIGHT off means Eye Mode OFF.
NOTE:
Blinking Green – Eye malfunction; clean eyes or make sure the marker is being fired with paint and air.
A blinking green LED is an indication that the there was an error in reading the previous shot command. The eyes
will still function normally even if the green LED is blinking.
NOTE:
When in Semi / 3 Burst Mode the lower LED light (Green or Orange) might reflect on the upper LED light.
LOWER LED LIGHT in Green is Semi-Auto ON.
LOWER LED LIGHT in Orange is 3 Burst ON.
NOTE:
When in 3 Burst mode the lower LED light (Orange) might reflect on the upper LED light. The safety is only
on when the upper LED light is RED.
TRIGGER ADJUSTMENT
#SCR006
#SCR005
#WRH004
VELOCITY ADJUSTMENT INCREASE / DECREASE
To INCREASE your velocity FPS (Feet Per Second) using the Allen wrench turn the Velocity Adjuster / Spring
Guide (#VTA001) clockwise.
To DECREASE your velocity FPS (Feet Per Second) using the Allen wrench turn the Velocity Adjuster / Spring
Guide (#VTA001) counter-clockwise.
NOTE:
Velocity Adjuster / Spring Guide (#VTA001) doesn't remove from the rear of the Sticker Plug (#STP001).
Adjusting the Top (#SCR006) located underneath the Trigger
Frame clockwise will swing the trigger closer to the touch
switch.
NOTE:
Adjusting the screw counter-clockwise will increase the
trigger gap.
HELPFUL HINT:
Over adjusting the screw to close won't allow
the trigger to activate the touch switch which will not allow
the marker to fire.
Adjusting the Middle (#SCR006) screw clockwise will shorten
the trigger stop the touch switch.
NOTE:
This will increase trigger sensitivity. Unscrewing it
counter clockwise will decrease trigger sensitivity.
Adjusting the Lower Screw (#SCR005) clockwise will shorten
the distance on trigger pull.
English
6
Publicidad
Capítulos
