Publicidad
Idiomas disponibles
Idiomas disponibles
JUNO IC1ALED NEW CONSTRUCTION RECESSED HOUSINGS
ELECTRICAL CONNECTION
INSTRUCTIONS
Knock-
out
Quick
Connector
0-10V Dimming Wires
(-U models only)
Figure 8
Step 1. Provide electrical service according to
national and/or local electrical codes to the junction
box located on the fixture plaster frame. Supply wire
insulation must be rated for at least 90°C.
Step 2. Remove junction box cover. Remove the
appropriate knockout to accommodate the type
of electrical supply being utilized (Fig. 8).
Metal Conduit. Remove appropriate round knock-
out(s) and connect conduit to junction box with
proper connectors (not supplied).
12/2 or 14/2 Non-Metallic Sheathed Cable
(Type NM-B). Remove appropriate D-shaped cable
knockout(s). Insert the NM-B cable through the
cable trap and make a 90˚L-shaped bend in cable as
shown (Fig. 9).
12/3 or 14/3 Cable (Type NM-B). Remove the
appropriate round knockout and connect cable
to junction box with proper electrical connectors
(not supplied).
Step 3. Strip supply wires 3/8" and insert each supply
wire into appropriate quick connector. Connect black
fixture wire to hot, white fixture wire to neutral and
green fixture wire to ground (Fig. 8).
Connect violet (+) and gray (-) dimmer wires
if utilizing 0-10V dimmer.
Step 4. Place all wiring and connectors back in
wiring box and replace cover.
NM-B Cable
NM-B Cable
Knockout
(D-Shaped)
NM-B Cable
Trap
(4 Places)
12/2 or 14/2 NM-B Installation
Figure 9
WARRANTY
5-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Technical Services Phone (888) 387-2212
1300 S. Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.acuitybrands.com/juno-recessed
©2017 Acuity Brands Lighting, Inc
INSTALLATION INSTRUCTIONS
FIXTURE DIMMING
IC1ALED Downlights with universal input
voltage (120VAC thru 277VAC) are dimmable
with the use of most 0-10V wall box dimmers.
IC1ALED Downlights with 120VAC input are
dimmable with the use of most incandescent,
magnetic low voltage or electronic low voltage*
wall box dimmers.
Consult Juno Product Services or website
for compatibility.
*Electronic low voltage dimmers require a
neutral wire connection in the wall box.
TRIM INSTALLATION
After ceiling is finished and painted, remove and
discard paint shield from fixture. Electronically
connect the trim to the wiring from the housing
using the clear connectors. Orient trim as desired
for proper aiming. Install trim into housing
utilizing the trim push-in springs (Fig. 10).
Clear Electrical
Connectors
Trim Push-In
Springs
Figure 10
DRIVER REPLACEMENT
Driver replacement must be performed by
a qualified electrician. Before servicing,
disconnect or switch off electrical supply to
fixture. Failure to do so can result in electrical
shock and/or injury.
120VAC IC1ALED Downlights:
Step 1. Remove trim from fixture by depressing
lock tab on electrical connector.
Step 2. Pull down inner housing to remove
from fixture. Disconnect red and black wires
connecting driver to inner housing and set aside
(Fig. 11).
Step 3. Remove junction box cover and
disconnect driver lead wires from supply
connections.
Rev 3/17
P3637
Step 4. Loosen wing
nuts and slide driver
out of the mounting
bracket. Remove from
housing (Fig. 12).
Step 5. Install new
driver into mounting
Figure 11
bracket and tighten
wing nuts to secure
in place.
Step 6. Re-connect all leads disconnected in
prior steps.
Step 7. Re-install inner housing and trim by
pushing up into housing.
Universal Voltage IC1ALED Downlights:
Step 1. Remove trim from fixture.
Step 2. Pull down inner housing to remove from
fixture (Fig. 11).
Step 3. Remove the wing nuts holding the
driver to the housing. Bring driver (with leads
connected) through ceiling opening (Fig. 13).
Step 4. Release all wires from driver by using
the quick disconnect slots located next to each
wire.
Step 5. Insert wires into the ports on the new
driver. Note: The red LED lead goes into the
brown opening and the black LED lead goes
into the yellow opening on the secondary side.
Step 6. Re-install driver in housing with wing nuts.
Step 7. Re-install inner housing and trim by
pushing up into housing.
Wing
Nuts
Figure 12
Wing
Nuts
Figure 13
Inner
Housing
Driver
2 of 2
Publicidad
