Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
STEP
STEP
5
STEP 5
Hang the Filter System Head
Hang the Filter System Head
Hang the Filter System Head
1
Align the System Head
1
A
Align the System Head
should be facing the incoming water supply.
on the pipes so that the inlet and outlet are in the correct locations. The "in" port on the System Head
should be facing the incoming water supply.
1
A
2
Align the System Head
on the pipes so that the inlet and outlet are in the correct locations. The "in" port on the System Head should
Allow the System Head to temporarily hang between the two cut plumbing pipes.
2
be facing the incoming water supply.
Allow the System Head to temporarily hang between the two cut plumbing pipes.
3
Apply plumber's tape or appropriate sealant to the fittings and lines, according to your system configuration.
2
Allow the System Head to temporarily hang between the two cut plumbing pipes.
3
Apply plumber's tape or appropriate sealant to the fittings and lines, according to your system configuration.
3
Apply plumber's tape or appropriate sealant to the fittings and lines, according to your system configuration.
4
Make all connections and tighten fittings.
4
4
Make all connections and tighten fittings.
Make all connections and tighten fittings.
NOTE: Keep the Filter System in an upright position.
NOTE: Keep the Filter System in an upright position.
NOTE: Keep the Filter System in an upright position.
5
5
Attach the Mounting Bracket
E
Attach the Mounting Bracket
5
E
Attach the Mounting Bracket
CAUTION
A grounding kit (not included) must be installed on water pipes if they are
A grounding kit (not included) must be installed on water pipes if they are
used to ground electrical systems, appliances or phones.
A grounding kit (not included) must be installed on water pipes if they are used to ground electrical systems, appliances or phones.
used to ground electrical systems, appliances or phones.
GROUNDING KIT (NOT INCLUDED)
STEP
STEP
6
STEP 6
Hang the Filter Housing
Hang the Filter Housing
Hang the Filter Housing
1
Insert the Filter Cartridge
1
B
Insert the Filter Cartridge
over standpipe in the bottom of the Filter Housing
2
Screw the Filter Housing back onto the System Head and hand-tighten. Using the Filter Housing Wrench
B
1
Insert the Filter Cartridge
over standpipe in the bottom of the Filter Housing
2
Screw the Filter Housing back onto the System Head and hand-tighten. Using the Filter Housing Wrench
NOTE: Do not over tighten.
2
Screw the Filter Housing back onto the System Head and hand-tighten
NOTE: Do not over tighten.
IMPORTANT: Do not over tighten.
WFPF13003B
WFPF13003B
WFPF13003B
5
A
on the pipes so that the inlet and outlet are in the correct locations. The "in" port on the System Head
E
to the wall using the four 2" Mounting Screws
to the wall using the four 2" Mounting Screws
to the wall using the four 2" Mounting Screws
CAUTION
CAUTION
GROUNDING KIT (NOT INCLUDED)
6
B
over standpipe in the bottom of the Filter Housing
.
Using the Filter Housing Wrench
F
F
or alternative fasteners (not included).
or alternative fasteners (not included).
F
or alternative fasteners (not included).
A
.
A
.
A.
D
, tighten 1/4 turn.
D
, tighten 1/4 turn.
5
6
5
5
5
5
IN
WATER
WATER
FLOW
FLOW
3
E
6
6
6
A
D
, tighten 1/4 turn.
E
IN
OUT
E
OUT
A
A
TO
HOUS
HOUSE
3
5
5
G
E
D
A
D
2
2
V4.1I
V4.0
TO
G
Publicidad
Tabla de contenido
