Cadence Option; Installation Fitting The Transmitter, Magnet; Installing The Battery In The Computer - VDO X Serie Instalacion Y Operación Manual

GB SLO PL JP
NAVIGATOR/SELECT
SELECT shows that there is a submenu for the main
NAVIGATOR menu. You open the submenu with
Set
B
You can set a starting value here and decide whether
the counter counts forwards or backwards from
this starting value. Further details in Chapter 5.7.
Reset
B
In the reset submenu you set the NAVIGATOR back
to zero. You leave the submenu by pressing C

3.2 Cadence option

The cadence menu is only available if
the cadence transmitter is installed,
B
the transmitter was recognized during pairing.
B
After pairing the cadence transmitter, the current
cadence is shown in section 2 of the display.
In function mode it is possible to select the
CADENCE/MORE menu using the buttons.
4 Installation
4.1 Fitting the transmitter, magnet and handlebar holder
Start by fitting the transmitter and magnet.
ATTENTION: The transmitting distance between the
transmitter and the computer on the handlebars
should not be more than 60 cm (transmission range).
8 X2DW
STOPWATCH
You can use the stopwatch to measure as many
M . times as you want. Maximum value: 23:59:59
HH:MM:SS. If the maximum value is exceeded,
the counter starts again at zero.
Start with M . Stop with M .
Reset with C for 3 seconds.
again.
Confirming with M opens the menu and gives you
access to the information.
Using you come to:
AVG CADENCE
B
MAX CADENCE
B
Resetting the trip data also sets the cadence data
back to zero.
step 1 Place the rubber pad under the transmitter.
Fit the transmitter on the same side of the fork
where you later want to fit the computer to the
handlebars (right or left) using the cable ties sup-
plied (loose at first, do not pull tight just yet).
VDO CYCLECOMPUTING
ATTENTION: The sensor mark on the transmitter
must point to the spokes.
Depending on the room available, the transmitter
can be fitted at the front on the forks, inner side
of the fork or backside of the forks.
step 2 Place spoke magnet around an outer
spoke. The silver middle of the magnet points
towards the transmitter. Align the magnet to the
sensor mark on the transmitter with a gap
of about 1 – 5 mm.
step 3 Align transmitter and magnet for good and
fasten in place: Pull cable ties tight and push
magnet in firmly.
4.2 Switching on the computer for the first time
Waking up from despatch mode
The computer is delivered with a battery installed.
To reduce the battery consumption, the computer
is put into despatch mode. The display is empty
(no display).
>>> P01

4.3 Installing the battery in the computer

Your VDO computer is supplied with a 3V battery
(type 2032).
The battery is already installed when supplied.
To change the battery, proceed as follows:
www.vdocyclecomputing.com
step 4 Decide whether fitting to handlebar or
stem and turn the base of the handlebar holder
by 90° accordingly. To do so, undo the screws in
the holder, take out the foot and turn it 90°, insert
and tighten the screws again.
>>> P04
ATTENTION: Do not over tighten screws.
step 5 Guide the cable ties through the slot in the
handlebar holder, place around the handlebars
or the stem and pull (do not pull tight just yet).
step 6 If fitting to handlebar: Align computer
angle to achieve optimum readability. Now pull
cable ties tight. Snip off protruding ends with
clippers.
>>> P02, Display see Chapter 4.4
To wake it up out of despatch mode, press the
button simultaneously for a few seconds.
The computer is now ready for use and tells you
so by showing the language setting.
See also Chapter 4.4
step 1 Place the battery in the computer casing
with the +terminal facing up.
step 2 Make sure that the battery does not
get wedged.
JP PL SLO GB
>>> P05
X2DW 9