Powersoft X Serie Manual De Instrucciones página 104

X4L
Specifications
Channel Handling
Number of output channels
Number of input channels:
Analog
AES3
Dante™*
* DANTE version only
Audio
Gain
Default Gain
Output Noise
A-Weighted @ 8 Ω - Analog to Analog / Digital to Analog
Dynamic Range
A-Weighted @ 8 Ω - Analog to Analog / Digital to Analog
Damping Factor @ 8 Ω, 20Hz - 500Hz
Slew Rate (input filter bypassed)
Frequency Response ( -3 dB , 1 W @ 8 Ω)
Crosstalk (1 kHz)
THD+N (from 0.1 W to Full Power)
DIM (from 0.1 W to Full Power)
Input Impedance
Input Acceptance
DSP
AD converters
DA converters
Sample rate converter
140 dB Dynamic Range - 0.0001 % THD+N
Internal precision
Delay
up to 100 ms per output for time alignment
Raised-cosine, custom FIR, parametric IIR:
Equalizer
Linear phase (FIR), hybrid (FIR-IIR), Butterworth, Linkwitz-Riley,
Crossover
Limiters TruePower™, RMS voltage, RMS current, Peak limiter
Damping control
Construction
Dimensions 483 mm x 88 mm x 495 mm (19.0 in x 3.5 in x 19.5 in)
Weight
102 | X Series
DO NOT CONNECT ANY
OUTPUT TERMINAL TO GROUND
OUT5 CH1/4
4 mono
4 (4x XLR)
4 (2x XLR)
16 (2x RJ45)
17 dB - 47 dB
(0.1 dB increments)
32 dB
< -67 dBV / < -67.5 dBV
113.5 dB / 114 dB
> 5000
> 50 V/µs
5 Hz - 22.5 kHz
-70 dB
< 0.5%
(typical < 0.01%)
< 0.5%
(typical < 0.01%)
20 kΩ Balanced
+27 dBu
Dual 24 bit 48 kHz Tandem architecture
®
with 129 dBA of dynamic range
Dual 24 bit 48 kHz Tandem architecture
®
with 121 dBA of dynamic range
24 Bit @ 44.1 kHz to 192 kHz
40 bit floating point
up to 2 s on input section
peaking, hi/lo-shelving, all-pass,
band-pass, band-stop, hi/lo-pass
Bessel: 6 dB/oct to 48 dB/oct (IIR)
Active DampingControl™
24 kg (52.9 lb)
Output Stage
Maximum output power per channel @ 8 Ω
Maximum output power per channel @ 4 Ω
Maximum output power per channel @ 2.7 Ω
Maximum output power per channel @ 2 Ω
Peak total output, all channels driven
Maximum unclipped output voltage
Maximum output current
*Measured by driving and loading symmetrically all the channels.
**Measured with half the channels at the stated power and the other channels at 25% of
that power (i.e. -6 dB)
AC Mains Power
Single Phase
Nominal Voltage
Operating Range
Current Draw
1/8 Maximum Output Power
1
Suggested circuit breaker
Three Phase
Nominal Voltage
Current Drawn from Each Single Phase
1/8 Maximum Output Power
1
Suggested circuit breaker (per phase)
Idle Consumption (all AC MAINS cases)
Max consumption (all AC MAINS cases)
1/8 Maximum Output Power into a typical 4 Ω loudspeaker
1
Thermal
Operating temperature
Cooling
Fan Noise - 1/8 Maximum Output Power (1m)
Thermal dissipation
Single phase
1/8 Maximum Output Power
1
1/8 Maximum Output Power into a typical 4 Ω loudspeaker. This is lower than with a
1
resistive dummy load thanks to the reactive behavior of loudspeakers. Please see our
white paper about this.
CH 1 CH 2 CH 3 CH 4
OUT 1 1+ 1- 2+ 2-
OUT 2 1+ 1-
OUT 3 1+ 1- 2+ 2-
OUT 4 1+ 1-
1+ 1- 2+ 2- 3+ 3- 4+ 4-
OUT 5
POWER OUTPUTS
Symmetrical* Asymmetrical**
4800 W 5000 W
6800 W 8400 W
7700 W 9600 W
8200 W 10000 W
32800 W
300 V
peak
140 A
peak
100 - 240 V @ 50/60Hz
90 - 264 V from DC to 200 Hz
26 A 13 A
rms
@115V @230V
C32 C32 / C16
173Y / 100 - 416Y / 240 V
3~, 3W+N+PE / 3W+PE
9 A 5 A
rms rms
@ 199V Y @ 400V Y
three phase 115V three phase 230V
C16
< 230 W
< 5000 W
0° - 35°C / 32° - 95°F
Fan, continuously variable
speed, temperature controlled
40 dBA SPL
1
115V 230V
2970 BTU/h 3650 BTU/h
rms