HIKVISION DS-PK-L Manual De Instrucciones

English
Diagram Reference
Components and Beeps
1
Alarm Keypad
Indicator
Set
Product Information
Fault
©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All
Network
rights reserved.
About this Manual
Armed/Disarmed
The Manual includes instructions for using and managing
the Product. Pictures, charts, images and all other
Alarm
information hereinafter are for description and explanation
Key
only. The information contained in the Manual is subject to
change, without notice, due to firmware updates or other
reasons. Please find the latest version of this Manual at the
Hikvision website (https://www.hikvision.com/).
Beeps
Please use this Manual with the guidance and assistance of
One Beep: Pressing keys/command timed out or too long.
professionals trained in supporting the Product.
Two Beeps: Valid command/Report uploaded.
Trademarks
Five Beeps: Invalid command/Failed to upload the report in 60s.
and other Hikvision's trademarks and logos
Continuous Beeping For Two Seconds: Fault prompt (Only for the Network
are the properties of Hikvision in various jurisdictions. Other
Control Panel)
trademarks and logos mentioned are the properties of their
Slowly Continuous Beeps: In the Entry/Exit delay status.
respective owners.
Rapidly Continuous Beeps: In the Entry/Exit delay status, 10 seconds countdown.
Rapid Beeps: Zone alarm/keypad not enrolled.
This product and - if applicable - the supplied
Three Long Beeps and Two Short Beeps: Keypad tampered.
accessories too are marked with "CE" and comply
Three Beeps: Keypad enrolled.
therefore with the applicable harmonized European
Address Settings
2
standards listed under the RE Directive 2014/53/EU,
the EMC Directive 2014/30/EU, the LVD Directive
Configure the address via DIP switch of the keypad before powering on the
2014/35/EU, the RoHS Directive 2011/65/EU. system. The address should be in the range (for Network Control Panel, 0 to 31;
for Hybrid Control Panel, 0 to 23). The address of each keypad should be unique.
The Input voltage should meet both the SELV (Safety
The binary value shown in the diagram is 00010, which means the decimal value
Extra Low Voltage) and the Limited Power Source
is 2. So the address of the keypad is 2.
according to the IEC60950-1 standard. Please refer
Wiring and Installation
3
to technical specifications for detailed information.
a. Dimension
2012/19/EU (WEEE directive): Products marked
b. Wiring
with this symbol cannot be disposed of as unsorted
Note: Hybrid control panel does not support Z1, GND, NO/NC, COM.
municipal waste in the European Union. For proper
c. Install Keypad
recycling, return this product to your local supplier
(1) Gangbox Mouting
upon the purchase of equivalent new equipment, or
(2) Wall Mouting
dispose of it at designated collection points. For
more information see: www.recyclethis.info
Operation Commands
4
Disclaimer Scan the QR code a to get programming manual of Hybrid control panel.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS
MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
Specification
SOFTWARE AND FIRMWARE, ARE PROVIDED "AS IS" AND "WITH
ALL FAULTS AND ERRORS". HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
Model
MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A
PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT Numeric key
YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT Function key
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, Display
CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION,
Keyfob
WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING
Tamper switch
NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
RS-485 interface
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR Sound
LOSS.
Tag/Card reading
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET
Power supply
PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL
Power
NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM consumption
CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER
Temperature
INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE
Humidity
TIMELY TECHNICAL SUPPORT IF REQUIRED.
Dimension
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL
(L × W × H)
APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR
ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
Weight
ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN
A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD
PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY,
Legal and Regulatory Information
INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND
OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR
ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR
PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE
DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL
WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY
NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN
SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND
THE APPLICABLE LAW, THE LATER PREVAILS.
INSTALLATION CAUTION
1. The additional force shall be equal to three times the
weight of the equipment but not less than 50N. The
equipment and its associated mounting means shall remain
secure during the installation. After the installation, the
equipment, including any associated mounting plate, shall not
be damaged.
2. Install the equipment according to the instructions in this
manual.
3. To prevent injury, this equipment must be securely
attached to the wall in accordance with the installation
instructions.
Solid Green: No Configuration
Flashing Green: In the Configuration Status
Solid Orange: System Fault Off: No Fault
Solid Green: All Enabled Channels Connected Normally
Off: Part of or All Enabled Channels Connected Abnormally
Off: Disarmed
Solid Blue: Armed
Flashing Red: Alarm Occurred/Tamper Alarm
Off: No Alarm
Query Project Bypass Medicine Scoll Up
Scoll Down
Fire Panic One-Push to Arm
It is required to insert the screw for tamper alarm.
DS-PK-L DS-PK-LR DS-PK-LRT DS-PK-LRTE
12 keys: 0 to 9, *, #
8 keys: Project/Query/Bypass/One-push to arm/Fire/Panic/Scroll
up/Scroll down
LCD screen
N/A N/A Two-way keyfob Two-way keyfob
1
1
buzzer
N/A N/A Support Support
12 V, 0.15 A
1.8 W
-10 °C to 55 °C
10% to 90%
164 mm × 124 mm × 31 mm
272 g
1
#
3
a
164.13 mm
30.96 mm
4
Hybrid control panel does not support Z1, GND,
NO/NC, COM.
Control Panel
D- D+ 12V GND
D- D+ 12V GND
c
(1) GANGBOX MOUNTING
b
(2) WALL MOUNTING
UD15865B-C
2
E.G
1 2 3 4 5
Lowbit Highbit
BIN=00010
DEC=2