Fein KBU 110-4 M Manual De Instrucciones página 31

OBJ_BUCH-0000000301-001.book Page 31 Monday, August 13, 2018 2:53 PM
Character
HSS Fe 400
T
a
L
pA
L
wA
L
pCpeak
K...
h
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 465 06 0). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
Magnetic core drill unit for drilling with core drill bits
and solid drill bits, reaming, countersinking and tapping
on materials with surfaces suitable for magnets in
weather-protected environments using the application
tools and accessories recommended by FEIN.
This power tool is also suitable for use with AC gener-
ators with sufficient power output that correspond to
the Standard ISO 8528, design type G2. This Standard is
particularly not complied with when the so-called dis-
tortion factor exceeds 10 %. When in doubt, please
refer to the generator instruction/specification guide.
These appliances are not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
Unit of measure- Unit of measure-
ment, international ment, national
mm mm
mm mm
mm mm
mm mm
mm mm
kg kg
°C °C
dB dB
dB dB
dB dB
2 2
m/s m/s
2 2
m/s m/s
m, s, kg, A, mm, V, m, s, kg, A, mm, V,
W, Hz, N, °C, dB, W, Hz, N, °C, dB,
2
min, m/s min, m/s
Explanation
Max. capacity in steel with up to
2
400 N/mm – high speed steel
(twist drill bit)
Max. drill chuck capacity
Reamer diameter
Counterboring diameter
Tap
Weight according to EPTA-Procedure 01
Allowable ambient temperature
Sound pressure level
Sound power level
Peak sound pressure level
Uncertainty
Vibrational emission value according to
EN 62841 (vector sum of three directions)
Mean vibrational value for core drilling
Basic and derived units of measurement
from the international system of units SI.
2
Safety instructions.
When performing drilling that requires the use of a fluid,
route the fluid away from the operator's work area or
use a collection system. Such precautionary measures
keep the operator's work area dry and reduce the risk
of electrical shock.
Operate the power tool by the insulated gripping sur-
faces, when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Contact of a cutting accessory with a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Wear hearing protection when drilling. Exposure to
noise can cause hearing loss.
When the application tool jams, stop applying pressure
and switch the power tool off. Check the cause of the
jam and apply corrective action to eliminate the cause of
the jamming application tool.
When restarting a core drill jammed in the workpiece,
check that the application tool rotates freely before
starting. If the application tool is jammed, it may not
start, may overload the power tool, or may cause the
core drill to release from the workpiece.
When drilling through walls or ceilings, ensure to pro-
tect persons and the work area on the other side. The
core bit may extend through the hole or the core may
fall out on the other side.
Do not use this tool for overhead drilling with fluid sup-
ply. Fluids entering the power tool will increase the risk
of electric shock.
Have the protective cable bushing replaced immediately
when damaged. A defective protective cable bushing
can lead to overheating of the machine.
en
31