Electrical Connections; Troubleshooting - Dri-Eaz F259 Manual Del Propietário

ELECTRICAL CONNECTIONS

Ace TurboDryers are designed to operate on a 115V/60 Hz elec-
trical connection. Make sure that the electrical outlet is grounded
and that all safety precautions are taken.
MAINTENANCE
Always turn off the power before performing maintenance proce-
dures. All the service procedures below are to be executed with
the unit unplugged. Perform before each use or as needed.
INSPECT ELECTRICAL SYSTEM: Inspect the electrical cord for
damage at regular intervals. Periodically, remove the housing and
inspect internal wiring for bare wires, insecure fasteners, and dis-
coloration. Remove and repair any damaged wiring as needed.
Failure to do so may lead to electrical shock or a fire hazard.
CLEAN GRILLS: Clean off any accumulated lint or other materials
from the protective grill cover. A buildup will reduce the airflow and
may cause the motor to overheat and become a fire hazard.
CLEAN EXTERIOR: Clean the housing with mild detergent and
water. Bring back the original shine with a vinyl cleaner and polish
like those used on automobile plastics.
EXTERIOR INSPECTION: Evaluate exterior components and
make sure they are properly installed. Listen to the unit for abnor-
mal sounds. Repair or replace components as needed.

TROUBLESHOOTING

In COLUMN 3, the technician in the field can handle "FS" or Field Solutions. Others solutions should be handled by a repair technician – an "AST"
or Authorized Service Technician.
WARNING: Execute all the service procedures below only with power turned off, i.e., unplugged.
PROBLEM
Motor won't run
Motor runs but blade turns er-
ratically or scrapes
Unit vibrates excessively
FOR PARTS AND SERVICE CALL YOUR LOCAL DISTRIBUTOR, or the Dri-Eaz Service Department at 800-932-3030.
07-01475G F259
CAUSE
No power to machine
Switch not turned on
Fan blade jammed
Intake or exhaust grill blocked
Switch is broken
Loose wiring
Severe jolt has caused motor mount to
bend and fan blade to rub
Accumulation of soil on fan blade
Fan blade has lost balance
Fan blade has been bent
Bent motor shaft
Periodic Maintenance (as needed)
Make sure unit is unplugged and the blade has stopped. Remove
four screws to remove each grill cover. This will permit access to
motor and fan blade for cleaning.
CLEAN COMPONENTS: Use compressed air or a vacuum to re-
move lint and dust from fan blade, motor and grill covers.
DO NOT WET MOTOR OR WIRING: To prevent damage to elec-
trical components, do not use a hose or pressure washer to clean
a TurboDryer. If electrical components do become wet, dry them
immediately.
MOTOR BEARINGS: The bearings on all Dri-Eaz
TurboDryers are permanently lubricated. Do not oil.
SPECIFICATIONS
Operating positions
Amperage
Power
Air movement
RPM
Static pressure
Motor rating
Motor speeds
Thermal protection
Switch
Fan blade
Dimensions
(H × D × W)
Use weight
Ship weight
Stackable
Handle
Cord length
Safety
Specifications are subject to change without notice. Some val-
ues are approximate.
WARNING: This product and other substances that may
become airborne from its use contain chemicals, inclu-
ding lead and phthalates, known to the State of California to cause
cancer, birth defects, or other reproductive harm. For more infor-
mation, go to P65Warnings.ca.gov
See
above SOLUTION
FS Plug in the unit; check circuit breaker or fuse
FS Turn on the switch
FS Remove material jamming blade
FS Turn machine off and allow to cool, then remove blockage
AST Call distributor or Dri-Eaz for replacement switch
AST Check wiring and tighten as needed
AST Remove motor from housing, then replace or repair bent motor
mount
FS Clean fan blade
AST Balance or replace fan blade
AST Replace fan blade
AST Replace motor
3
6
1.5A
115V / 60Hz
1,954 CFM | 3320 CMH
1670 low 1756 high
0.6 in. | 1.5 cm
¼ hp TEAO
2-speed PSC
Thermal cut-off
2-speed rocker
16.5 in. | 41.9 cm axial
24 × 20.3 × 19 in.
61 × 51.5 × 48.3 cm
33 lbs. | 15 kg
38 lbs. | 17 kg
Yes
Molded
25 ft. | 7.6 m
UL/cUL listed
Dri-Eaz Products, Inc.