Tabla De Contenido; Table Of Contents; Safety Information - ETI Solid State Lighting 54296146 Guía De Uso Y Cuidado

Table of Contents

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Planning Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Hardware Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety Information

WARNING: Carefully read and understand the information
given in this manual before beginning the assembly and
installation. Failure to do so so could lead to electric shock,
fire, or other injuries which could be hazardous or even fatal.
WARNING: Ensure the electricity to the wires you are
working on is shut off. Either remove the fuse or turn off the
circuit breaker
.
WARNING: Risk of fire or electric shock. Installation of this
LED Retrofit Kit assembly requires a person familiar with the
construction and operation of the light fixture's/luminaire's
electrical system and the hazard involved. If not qualified, do
not attempt installation. Contact a qualified electrician.
WARNING: Install this kit only in luminaires (light fixtures)
that have the construction features and dimensions shown in
the photographs and/or drawings included in these installation
instructions.
WARNING: Do not make or alter any open holes in an
enclosure of wiring or electrical components during kit
installation.
WARNING: To prevent wiring damage or abrasion, do not
expose wiring to edges of sheet metal or other sharp objects.
WARNING: Installers should not disconnect existing wires
from lampholder terminals to make new connections at
lampholder terminals. Instead installers should cut existing
lampholder leads away from the lampholder and make new
electrical connections to lampholder lead wires by employing
applicable connectors.
Installation Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connection Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation - Strip Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation - Other Fixtures . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
NOTICE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
□ Reorient or relocate the receiving antenna.
□ Increase the separation between the equipment and the receiver.
□ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
□ Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.
WARNING: To avoid potential fire or shock hazard, do not
use this retrofit kit in luminaires employing shunted bi-pin
lampholders. Note: Shunted lamp holders are found only in
fluorescent luminaires with Instant-Start ballasts. Instant-
start ballasts can be identified by the words "Instant Start" or
"I.S." marked on the ballast. This designation may be in the
form of a statement pertaining to the ballast itself, or may
be combined with the marking for the lamps with which the
ballast is intended to be used, for example F40T12/IS. For more
information, contact the LED luminaire retrofit kit manufacturer.
2 2