Firmware Update; Bionova ® Traceability Software; Bionova ® Wilink Connection - Terragene IC10/20FRLCD Manual De Instrucciones

Additional features

Firmware update

Bionova IC10/20FRLCD Auto-reader Incubator allows the
®
update of its firmware (program inside the Incubator that
controls and defines its different features) by using the firmware
update utility Bionova Bioupdate. Bionova
®
connects to the internet to verify, download, and install, the
latest firmware version available for your incubator. The update
process only lasts a few seconds and is carried out without the
loss of any Incubator's data. Please visit www.terragene.com/
software to download Bionova
Update process
Before updating the device, make sure that the Bionova
Traceability Software is closed. Power Off the Incubator for five
seconds, afterwards Power On the Incubator and follow the
next steps:
1.Connect the Incubator to your Local Network following the
instructions on Local Network connection section. Make sure
your PC is connected to the same network, and that an active
internet connection is available.
2.Run Bionova Bioupdate.
®
3. Select the Incubator you want to update, check that the IP is
correct. Press the Start button to update.
4.Wait until the software indicates that the update process has
been completed. The Incubator will print an update confirmation
ticket. If it was already up to date, the ticket will not be printed.
NOTE: This process must be repeated every time that a
new firmware version is available, this will be informed in
the Terragene S.A. website.
®
NOTE: When it is necessary to update the LCD Screen
graphical environment, the update process may take up
to 30 minutes. Plan accordingly.
Bionova Traceability Software
®
Managing results with Bionova
Bionova Traceability Software is a proprietary software
®
designed by Terragene to manage and store the results of Self-
®
contained biological indicators and Hygiene Monitoring System
Indicatorsin a secure and user-friendly way.
Bionova Traceability Software allows matching the information
®
of an Indicator result with the sterilizer or washing machine used,
the operator, cycle characteristics, and all relevant information
for allowing each institution achieve reliable documentation
compliance and safe-keeping. All saved information is stored
in a password protected encrypted database to assure its
integrity. Furthermore, all previously saved information can be
reprinted at any time to generate a hard copy of the results.
Visit www.terragene.com/software to download the latest
version of Bionova Traceability Software, its User Manual, and
®
to check its newest features and capabilities.
Bioupdate
®
Bioupdate.
®
Traceability Software
®
IC10/20FRLCD Page 14
Using Bionova Traceability Software
®
To use Bionova Traceability Software along with your incubator,
®
please download the software from our webpage and install it
in a compatible Personal Computer (PC). The PC minimum
requirments are listed in the Traceability Software User Manual.
After the installation is complete, connect your Bionova
IC10/20FRLCD via its Ethernet port to a PC following the
instructions on Local Network connection section and run
Bionova Traceability Software. When the Incubator is connected
®
to the Traceability Software succesfully, the Bionova
Indicator will change
Please check the Traceability Software's User Manual for more
® information about the connection and installation procedure.
Bionova Wilink connection
®
Bionova Wilink is a WI-Fi connectivity accessory for Bionova
®
IC10/20FRLCD. Wilink can be used for connecting the Incubator
to a WI-Fi Network directly, so the incubator connects to your
Local Network by WI-Fi instead of using an Ethernet cable. Please
visit www.terragene.com to learn more about Bionova
Connection
®
from to .
Wilink.
®
®
®