Assembly And Adjustments - DeWalt DCN693 Traducido De Las Instrucciones Originales

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
WARNING: Use only D
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (Fig. 2)
NOTE: Make sure your battery pack (L) is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack (L) with the rails inside
the tool's handle.
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that you
hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release button (U) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2, 2A)
Some D WALT battery packs include a fuel gauge
e
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (P). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Rotating Rafter/Belt Hook (Fig. 6)
The rafter/belt hook (J) and can be easily positioned
to the left or right of the tool to accommodate left-
or right-handed users.
If use of the hook is not desired at all, it can be
rotated to the front or back of the handle base.
Loading the Tool (Fig. 4)
WALT battery
e
1. Slide the spring-loaded pusher latch (H) to the
base of the magazine to lock it into place.
2. Select an appropriate collated nail stick. (Refer
to Technical Data.) D
recommend that you use D
fix nails.
3. Insert nail strips into the loading slot of the
magazine, making sure the nail heads align
correctly with the slot opening.
4. Close the magazine by releasing the pusher
latch. Carefully allow the latch to slide forward
and engage the nail strip.
Dry Fire Lock out
The nailer is equipped with a dry drive lock out
which restricts the tool from actuating when the
magazine is nearly empty. When approximately 4
to 6 nails remain in the magazine, the tool dry drive
lock actuates. Refer to Loading the Tool to reload
a stick of collated nails.
NOTE: If heavy force is placed on the tool it is
possible to override the lock out. This protects the
tool from potential damage if dropped.
Adjusting the Driving Depth (Fig. 5)
The nail driving depth can be adjusted using the
depth adjustment wheel.
1. To drive the nail shallower, rotate the depth
adjustment wheel (D) to the left, toward the
shallow nail icon.
2. To sink a nail deeper, rotate the depth
adjustment wheel (D) to the right, toward the
deeper nail icon.
WARNING: Always engage the trigger
safety lock-off (B) and disconnect battery
pack before loading and unloading
fasteners.
WARNING: Fasteners used to
install metal connectors must meet
the requirements of the applicable
building codes and must be installed
in compliance with code requirements
and metal connector hardware supplier
specifications. Failure to properly install
connectors may result in structural
failures.
WALT would always
e
WALT branded first
e
WARNING: Since accessories, other
than those offered by D WALT, have not
e
been tested with this product, use of
such accessories with this tool could be
hazardous. To reduce the risk of injury,
only D WALT recommended accessories
e
should be used with this product.
english
53