3M SEALED-BLOK 3400944 Manual Del Usuario página 12

Ocultar thumbs Ver también para SEALED-BLOK 3400944:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 49
RETRIEVAL OVERLOAD:
drive components and attached person. Avoid line slack while in Retrieval mode. Also, monitor the individual during retrieval
to ensure they are not subjected to excessive force from continued lifting after entanglement on an obstruction.
NOTE:
A minimum load of 75 lbs (33.9 kg) is required to lower or pay out the Lifeline. A force of 30 lbs (0.13 kN) is required
to operate the Retrieval system when loaded to capacity.
CAUTION:
Stop cranking when the Lifeline is fully extended or retracted. Continued cranking can damage components.
4.8
RETRIEVAL DISENGAGEMENT: To disengage Retrieval mode:
CAUTION:
When Retrieval mode is disengaged, any extended Lifeline will retract into the SRL. To avoid possible
injury, retract the Lifeline prior to disengagement or hold onto the Lifeline.
1. Remove any load from the Lifeline.
2. Pull and hold the Shift Knob in the unlocked position.
3. Pull the Crank Arm out to disengage and then release the Shift Knob.
4. Pull out and rotate the Retrieval Handle down toward the SRL Body to stowed position.
5.0 INSPECTION
5.1
i-Safe™ RFID TAG: The Self-Retracting Lanyard includes an i-Safe™ Radio Frequency Identifi cation (RFID)
tag. The RFID tag can be used in conjunction with the i-Safe handheld reading device and web based portal
to simplify inspection and inventory control and provide records for your fall protection equipment. For
details, contact a Capital Safety Customer Service representative (see back cover); or if you have already
registered, go to http://isafe3.capitalsafety.com/Pro/. Follow the instructions provided with your i-Safe
handheld reader, or on the web portal, to transfer your data to your web log.
5.2
INSPECTION FREQUENCY: The Sealed-Blok Self-Retracting Lanyard must be inspected at the intervals
defi ned in Section 2.2 - Inspection Frequency". Inspection procedures are described in the "Inspection and
Maintenance Log" (Table 2).
IMPORTANT:
If the Self-Retracting Lanyard has been subjected to fall arrest or impact forces it must be immediately
removed from service, marked as "UNUSABLE", and inspected by a Competent Person per instructions in Table 2 to
determine service options.
IMPORTANT:
Extreme working conditions (harsh environments, prolonged use, etc.) may require increasing the
frequency of inspections.
5.3
UNSAFE OR DEFECTIVE CONDITIONS: If inspection reveals an unsafe defective condition, remove the
Self-Retracting Lanyard from service immediately, mark as "UNUSABLE", and perform a Competent Person
inspection to determine service options.
NOTE:
Only Capital Safety or parties authorized in writing may make repairs other than FAST-Line Lifeline
replacement to this equipment.
5.4
PRODUCT LIFE: The functional life of DBI-SALA Self-Retracting Lanyards is determined by work conditions
and maintenance. As long as the product passes inspection criteria, it may remain in service.
6.0 CLEANING, SERVICE, STORAGE, AND TRANSPORT
6.1
CLEANING: Cleaning procedures for the Self-Retracting Lanyard are as follows:
Periodically clean the exterior of the SRL using water and a mild soap solution. Position the SRL so
excess water can drain out. Clean labels as required.
Clean lifeline with water and mild soap solution. Rinse and thoroughly air dry. Do not force dry with
heat. An excessive buildup of dirt, paint, etc. may prevent the lifeline from fully retracting back into the
housing causing a potential free fall hazard. Replace lifeline if excessive buildup is present.
6.2
SERVICE: FAST-Line Lifelines can be replaced in the fi eld by a Competent Person
required FAST-Line Lifeline Replacement Kit. Install the lifeline per the instructions in the Service Manual
(5903076) include with the FAST-Line kit. Always perform a complete Competent Person inspection after
replacing the FAST-Line Lifeline. Additional service, determined from the Competent Person inspection, must
be completed by an authorized service center. Do not attempt to disassemble the SRL or lubricate any parts.
6.3
STORAGE AND TRANSPORT: Store and transport Self-Retracting Lanyard in a cool, dry, clean environment
out of direct sunlight. Avoid areas where chemical vapors may exist. Thoroughly inspect the SRL after any
period of extended storage.
1 Competent Person:
An individual designated by the employer to be responsible for the immediate supervision, implementation, and monitoring of the
employer's managed fall protection program who, through training and knowledge, is capable of identifying, evaluating, and addressing existing and potential fall
hazards, and who has the employer's authority to take prompt corrective action with regard to such hazards.
Sealed-Blok SRL-Rs do not incorporate an Overload Clutch to limit the force exerted on the
12
. See Figure 1 for the
1

Publicidad

Tabla de contenido
loading

Tabla de contenido