Angle Grinder; Noise/Vibration Information - Milwaukee AG 11-115 Manual Original

TECHNICAL DATA
AG 11
Rated input .................................................................................................
Max. no-load speed ................................................................................
Grinding disk diameter..................................................................................
Thread of work spindle ..................................................................................... M 14 ......................... M 14 ......................... M 14
Weight without cable.....................................................................................

Noise/Vibration Information

Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K=3 dB(A)) ................................................................
Sound power level(K=3 dB(A)) ..................................................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Surface grinding: vibration emission value a
Uncertainty K .................................................................................................
Disk sanding: vibration emission level a
Uncertainty K .................................................................................................
For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories
or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually
doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm,
organisation of work patterns.
WARNING!
Read all safety warnings and all instructions, including those given in
the accompanying brochure. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Safety Warnings Common for Grinding, Sanding, Wire Brushing or
Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder, sander,
wire brush, or cut-off tool. Read all safety warnings, instructions,
illustrations and specifications provided with this power tool. Failure
to follow all instructions listed below may result in electric shock, fi re and/or
serious injury.
b) This electric tool is not suitable for polishing. Using the electric tool
for purposes other than those for which it is designed may cause dangers and
injuries.
c) Do not use accessories which are not specifically designed and
recommended by the tool manufacturer. Just because the accessory can
be attached to your power tool, it does not assure safe operation.
d )The rated speed of the accessory must be at least equal to the
maximum speed marked on the power tool. Accessories running faster
than their rated speed can break and fly apart.
e) The outside diameter and the thickness of your accessory must be
within the capacity rating of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
................................................
h
........................................................
h
AG 11-115 AG 11-125
1100 W .................1100 W .................. 1100 W
10 000 min ...........10 000 min
-1
115 mm ................125 mm ................. 125 mm
2,5 kg ....................2,5 kg ................... 2,5 kg
90,5 dB(A) .............90,5 dB(A) ............ 90,5 dB(A)
101,5 dB(A) ...........101,5 dB(A) .......... 101,5 dB(A)
6,3 m/s .................6,3 m/s
2
1,5 m/s .................1,5 m/s
2
5,0 m/s .................5,0 m/s
2
1,5 m/s .................1,5 m/s
2
f) The arbour size of wheels, flanges, backing pads or any other
accessory must properly fit the spindle of the power tool. Accessories
with arbour holes that do not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect the
accessory such as abrasive wheels for chips and cracks, backing pad
for cracks, tear or excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for damage or install an
undamaged accessory. After inspecting and installing an accessory,
position yourself and bystanders away from the plane of the rotating
accessory and run the power tool at maximum noload speed for one
minute. Damaged accessories will normally break apart during this test time.
h) Wear personal protective equipment. Depending on application,
use face shield, safety goggles or safety glasses. As appropriate,
wear dust mask, hearing protectors, gloves and shop apron capable
of stopping small abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by various operations. The
dust mask or respirator must be capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area. Anyone
entering the work area must wear personal protective equipment.
Fragments of workpiece or of a broken accessory may fly away and cause injury
beyond immediate area of operation.
j) Hold power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a „live" wire may make exposed
metal parts of the power tool „live" and could give the operator an electric
shock.

Angle Grinder

AG 11-125 X
.......... 10 000 min
-1 -1
................. 6,3 m/s
2 2
................. 1,5 m/s
2 2
................. 5,0 m/s
2 2
................. 1,5 m/s
2 2
English
11
GB