Using The Dust Collector; When The Work Is Done - UFESA AT9320 Instrucciones De Uso

Figure 3
Attach the floor brush to the telescopic tube
Figure 4
Disconnect the telescopic tube and adjust its length by mo-
ving the adjusting button in the direction of the arrow.
Figure 5
Holding the power cord by the plug, pull out the required
length and plug it into the mains socket.
Figure 6
Press the on/off button in the direction of the arrow to switch
your vacuum cleaner on/off.
Figure 7
Set the power with the regulator.
Figure 8
The intensity can be regulated from the hand grip. Opening
the flap reduces suction whereas closing it increases suction.
Figure 9
Attach the nozzles to the suction pipe or handle as required:
a) Crevice nozzle. Long nozzle for vacuuming deep grooves
and nooks, etc.
b) Upholstery nozzle for vacuuming upholstered furniture,
curtains, etc.
c) Upholstery nozzle to prevent surfaces from being dama-
ged.
Figure 10
You can use the parking aid on the back of the vacuum cleaner
if you wish to stop vacuuming for a short time.
Slide the catch on the floor tool into the groove at the rear of
the appliance.
Figure 11
The appliance can also be carried using the two handles when
vacuuming steps, for example.

WHEN THE WORK IS DONE

Figure 12
When you have finished using the appliance press the On/Off
pedal. Disconnect the plug from the mains and wind in the
cord by pressing down on the automatic cord rewind pedal.
Figure 13
To store or transport the vacuum cleaner, use the storage aid
on the underside of the vacuum cleaner.
Stand the vacuum cleaner up on its end. Slide the catch on the
floor tool into the groove on the underside of the appliance.
You have purchased a floor vacuum cleaner which can vacuum
up any type of dry dirt using the dust collector or dust bag.
We recommend that you use:
- the dust collector, in particular for your hobbies, e.g. to re-
move wood shavings, etc.
- the dust bag principally for everyday household cleaning.

USING THE DUST COLLECTOR

Figure 14
Set the power setting to maximum for the best results when
vacuuming.
We recommend that you reduce the setting only when vacuu-
ming very delicate materials.
Attention! The cover on this appliance cannot be closed
if the dust collector or filter bag are not present inside.
Do not force it shut and check that the desired dirt co-
llection system is fitted correctly.
Emptying the dust collector
To achieve an optimal result when vacuuming, the dust collec-
tor should be emptied each time the vacuum cleaner is used.
Figure 15
Turn the dust compartment locking lever in the direction of the
arrow to open the dust compartment cover.
Figure 16
Remove the dust container from the appliance.
Figure 17
To open the container base cover, press the button and empty
the contents into a dustbin.
– Close the bottom flap so that it can be heard snapping into
position.
Figure 18
Put the dust bag back into the vacuum cleaner and close the
dust bag compartment lid.
!Caution: The inside of the dust container may become
scratched with use and Stara to look opaque. This does
not, however, affect the performance of the vacuum clea-
ner in any way, i.e. it will continue to function as normal.
CLEANING THE HEPA FILTER AND THE NYLON
FILTER FOR THE DUST CONTAINER
The filters must be cleaned:
– After any operating malfunctions, i.e. after a blockage is
cleared.
At least every six months.
Figure 19
Remove the HEPA filter by pulling it straight out.
Turn the nylon filter anti-clockwise to remove it and pull it out
of its housing.
Figure 20
- Wash the HEPA and nylon filters. Then leave them to dry for
at least 24 hours.
Once clean and dry fit them back into their housings on the
container.
Place the container back into its housing on the vacuum clea-
ner.
VACUUMING WITH THE FILTER BAG
If necessary, the filter bag can also be used instead of the dust
collector.