Learning Of Opening And Closing Values - Key Automation HALO Instrucciones Y Advertencias Para Su Instalación Y Uso

RADIO CONTROL DELETING
PHASE DESCRIPTION
1 Press the RADIO button until the LED L2 lights up (about 3 seconds)
Within 10 seconds, press and hold a button of the radio control that you wish to delete until the LED L2 on
2
the receiver goes off. Release the radio control button
3 After about 1 second from releasing the button the LED L2 on the receiver starts to flash
4 Confirm deleting by pressing the RADIO button
5 If deleting has been successful, the LED L2 will emit one long flash
Note After 10 seconds of inactivity, the receiver automatically exits the deleting phase
COMPLETE DELETING OF RECEIVER MEMORY/RECEIVER RESETTING
PHASE DESCRIPTION
Press and hold the RADIO button until the LED L2 lights up (about 3 seconds) and then goes off (about 3
1
seconds). Release the button
2 After about 1 second from releasing the button the LED L2 on the receiver starts to flash
3 To delete all the memory, press the RADIO button upon the third flash
4 If deleting/resetting has been successful the LED L2 will emit one long flash
REMOTE STORAGE OF A RADIO CONTROL WITH RADIO CONTROL ALREADY STORED
It is possible to store a transmitter without accessing the re-
ceiver. It is necessary to have previously stored a transmitter
and follow the procedure below.
PHASE DESCRIPTION
1 Press and hold the button of the new radio control that you wish to store for at least 5 seconds
Press and hold the button of the old radio control to be copied for at least 3 seconds (if the previous phase
2
1 was successful, the automation system will not move)
3 Press and hold the button of the new radio control that you wish to store for at least 3 seconds
Press and hold the button of the old radio control to be copied for at least 3 seconds to confirm and exit the
4
programming phase
Note After 10 seconds of inactivity, the receiver automatically exits the programming phase
4.12 - Learning opening and closing values
If you have a KUBE PRO wireless module, connect it to the control
unit (FIG. 49, 50) and follow the instructions on the screen.
If you have a DYL cable module, connect it to the control unit and
follow the instructions on the screen.
ATTENTION !
If you had previously connected the KUBE PRO module, KUBE
or the DYL programmer, power the device off for a few seconds
to be able to use the manual procedure.
The photocell contact must be connected to the COM and PH ter-
minals. To bypass the photocell, move the left-hand dip switch
upwards. After having activated the dip switch, the LEDs L1
and L2 start to flash at a fast rate.
ATTENTION !
CONFIRM INPUT PH DEACTIVATION BY PRESSING THE MENU
PHASE DESCRIPTION
1 Program a remote control if you do not have a remote control already stored or work the SBS button of the control unit
2 If the slider has never been moved by hand, the door, with the slider attached to the guide, must be in its partial opening position
Press the SBS button of a stored remote control or the SBS button on the control unit or an external button connected to the SBS
3
input of the control unit
The remote copying procedure must be performed in the area
covered by the receiver.
AND RADIO BUTTONS SIMULTANEOUSLY AND HOLDING
THEM DOWN UNTIL THE LEDs L1 AND L2 STOP FLASHING.
The inputs of the sensitive EDGE must be connected to the EDGE
and EDGE terminals. To bypass the sensitive edge, move the
right-hand dip switch upwards. After having activated the dip
switch, the LEDs L1 and L2 start to flash at a fast rate.
ATTENTION !
CONFIRM INPUT EDGE DEACTIVATION BY PRESSING THE
MENU AND RADIO BUTTONS SIMULTANEOUSLY AND HOLD-
ING THEM DOWN UNTIL THE LEDs L1 AND L2 STOP FLASH-
ING.
Otherwise proceed as described below:
EN
EXAMPLE
(>3s)->
->
0,5s 0,5s
3s
EXAMPLE
(>3s)-> (>3s)->
(1s)+ (1s)+
EXAMPLE
>5s
>3s
>3s
>3s
9