Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Website:
www.horizonglobal.com
Technical Assistance: 800-632-3290
TechnicalSupport@horizonglobal.com
To prevent SERIOUS INJURY, DEATH or PROPERTY DAMAGE:
ALWAYS read, understand and follow warnings and instructions
for your hitch BEFORE installation. Keep for future reference.
DO NOT cut, weld or modify this receiver.
CHECK all fasteners are tight and your hitch is securely mounted
to your vehicle periodically.
ALWAYS read, understand and follow all warnings and
instructions for your vehicle and for other accessories you will use
with your hitch BEFORE use.
LOAD the trailer heavier in front.
DO NOT exceed lower of towing vehicle manufacturer's rating or:
Hitch Type
Max Gross Trailer
Weight Carrying
6000 lb. (2721 kg)
Weight Distributing
ALWAYS wear your seatbelt.
SLOW DOWN when towing, NEVER exceed any posted speed limit.
If EXCESS SWAY occurs, take your foot off the gas pedal and hold
the steering wheel as steady as possible. DO NOT apply your
brakes and DO NOT speed up.
©2020 Horizon Global™ Corp - Printed in Mexico
Installation Instructions
PART NUMBERS: 76338, 84338, CQT76338
Max Tongue
Weight
Weight
600 lb. (272 kg)
N/A
N/A
LIMITED LIFETIME WARRANTY
Limited Lifetime Warranty ("Warranty"). Horizon Global ("We", "Us" or "Our")
1.
warrants to the original consumer purchaser only ("You" or "Your") that the product will be
free from material defects in both material and workmanship, ordinary wear and tear
excepted. The Warranty is valid only if (a) the products are returned to Us for inspection and
testing; (b) Our inspection discloses to Our satisfaction that any alleged nonconformance are
material and have not been caused by misuse, neglect, wear and tear, improper installation,
unsuitable storage, improper repair, alteration, or accident; and (c) the products were
installed, maintained and used in accordance with Our instructions. THE WARRANTY IS
MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (OTHER
THAN THE WARRANTY OF TITLE AS PROVIDED BY THE UNIFORM
COMMERCIAL CODE IN EFFECT IN MICHIGAN), INCLUDING WITHOUT
LIMITATION, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, SAID WARRANTIES BEING EXPRESSLY DISCLAIMED.
2.
Obligations of Purchaser. To make a Warranty claim, contact Us at our principal address of
47912 Halyard Drive, Suite 100, Plymouth, MI 48170, 1-800-632-3290, identify the product
by model number, and follow the claim instructions that will be provided. Any returned
product that is replaced by Us becomes our property. You may be responsible for return
shipping costs. Please retain your purchase receipt to verify date of purchase and that You
are the original consumer purchaser. The product and the purchase receipt must be provided
to Us in order to process Your Warranty claim.
3.
Exclusive Remedy. Product replacement is Your sole and exclusive remedy under this
Warranty. We shall not be liable for service or labor charges incurred in removing or
replacing a product. IN NO EVENT WILL WE BE RESPONSIBLE FOR ANY INDIRECT,
SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES.
4.
Assumption of Risk. You acknowledge and agree that any use of the product for any
purpose other than the specified use(s) stated in the product instructions is at Your own risk.
5.
Governing Law. This Warranty gives You specific legal rights, and You also may have
other rights which vary from state to state. This Warranty is governed by the laws of the
State of Michigan, without regard to rules pertaining to conflicts of law. The state courts
located in Oakland County, Michigan shall have exclusive jurisdiction for any disputes
relating to this Warranty.
Rev 8/2015
Sheet 1 of 24
Scan for safe towing
tip, or visit
http://qr.towingpro
ducts.net/qrproduct
s/qr-product
76338NP
06-17-20
Rev. A

Publicidad

loading

Resumen de contenidos para Horizon Global CQT76338

  • Página 1 TechnicalSupport@horizonglobal.com LIMITED LIFETIME WARRANTY Limited Lifetime Warranty (“Warranty”). Horizon Global ("We", “Us” or “Our”) warrants to the original consumer purchaser only ("You" or “Your”) that the product will be To prevent SERIOUS INJURY, DEATH or PROPERTY DAMAGE: free from material defects in both material and workmanship, ordinary wear and tear •...
  • Página 2: Installation Instructions

    MANUFACTURER’S RATING OR: Hitch Type Max Gross Trailer Weight Max Tongue Weight Weight Carrying 6000 lb. (2721 kg) 600 lb. (272 kg) Weight Distributing Hitch Illustration ©2020 Horizon Global™ Corp - Printed in Mexico Sheet 2 of 24 76338NP 06-17-20 Rev. A...
  • Página 3 Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. ©2020 Horizon Global™ Corp - Printed in Mexico Sheet 3 of 24...
  • Página 4 Remove rear bumper fascia - a.) Remove heat shields -On the underside of vehicle, driver side. Using a T25 star driver, remove 5 screws and remove heat shield. Repeat steps on passenger side. Set fasteners and heat shield aside to be reinstalled. ©2020 Horizon Global™ Corp - Printed in Mexico Sheet 4 of 24...
  • Página 5 2e.) Using a plastic trim tool, partially remove the fascia by gently pulling fasteners aside to be reinstalled. rearward while releasing the clips of the wheel well trim. Only remove as far as shown in Figure 2 ©2020 Horizon Global™ Corp - Printed in Mexico Sheet 5 of 24 76338NP 06-17-20...
  • Página 6 Return bumper beam and support band to owner. See Figure 1. End panel Support Band Bumper beam Existing M12 Bolts (8) Places Figure 1 ©2020 Horizon Global™ Corp - Printed in Mexico Sheet 6 of 24 76338NP 06-17-20 Rev. A...
  • Página 7 5. Trim fascia –Locate the center of the fascia. Using a tape measure, marker, and utility knife, cut a notch in the bottom of fascia approximately 4’’ wide by 4” tall. See Figure 3. Note: Be sure area is clear of all electrical wiring before trimming. Area to trim 4” 4” Figure 3 ©2020 Horizon Global™ Corp - Printed in Mexico Sheet 7 of 24 76338NP 06-17-20 Rev. A...
  • Página 8 6. Reinstall fascia – Reconnect all wiring first. Then reinstall the fascia using original hardware removed in steps 1 and 2. ©2020 Horizon Global™ Corp - Printed in Mexico Sheet 8 of 24 76338NP 06-17-20 Rev. A...
  • Página 9: Garantie À Vie Limitée

    TechnicalSupport@horizonglobal.com GARANTIE À VIE LIMITÉE Garantie à vie limitée (« Garantie »). Horizon Global (« Nous », « Notre ») garantit à l’acheteur initial seulement (« Vous », « Votre ») que le produit sera exempt de vices de Pour prévenir les blessures SÉVÈRES, FATALES ou les DOMMAGES matières et de fabrication, exception faite de l’usure normale.
  • Página 10 Instructions d’installation Numériser pour des instructions avec NUMÉROS DE PIÈCES : 76338, 84338, CQT76338 PHOTOS ou visiter Site Internet: www.horizonglobal.com http://qr.towingprod ucts.net/qrproducts/q Assistance technique: 800-632-3290 r-product TechnicalSupport@horizonglobal.com Applications : Durée de l'installation : 75 min Années Marque Modèles La valeur indiquée ci-dessus est la durée...
  • Página 11 Instructions d’installation Panneau d'extrémité Zone à Visserie similaire NUMÉROS DE PIÈCE : 76338, 84338, CQT76338 découper des deux côtés 4 po 4 po Boulons M12 existants Figure 3 Huit (8) endroits Figure 1 Toujours porter des LUNETTES DE PROTECTION pour installer l'attelage.
  • Página 12 Retirer le carénage de pare-chocs arrière - a.) Retirer les écrans thermiques sur le dessous du véhicule, côté conducteur. À l’aide d’un tournevis étoilé T25, retirer cinq (5) vis et enlever l’écran thermique. Répéter ces étapes du côté passager. Mettre la visserie et les écrans thermiques de côté pour la réinstallation. ©2020 Horizon Global™ Corp. - Imprimé au Mexique Feuille 12 de 24...
  • Página 13 Retirer la garniture seulement jusqu’à l’endroit indiqué sur la Figure 2. ©2020 Horizon Global™ Corp. - Imprimé au Mexique Feuille 13 de 24 76338NP 06-17-20 Rev.
  • Página 14 Conserver les boulons pour l’installation de l’attelage. Voir la Figure 1. Panneau d'extrémité la bande de support la poutre pare-chocs Boulons M12 existants Huit (8) endroits Figure 1 ©2020 Horizon Global™ Corp. - Imprimé au Mexique Feuille 14 de 24 76338NP 06-17-20 Rev. A...
  • Página 15 4 po (large x haut) dans le bas du carénage. Voir la Figure 3. Remarque : S’assurer que la zone est libre de tout câblage électrique avant de découper. Zone à découper 4” 4” Figure 3 ©2020 Horizon Global™ Corp. - Imprimé au Mexique Feuille 15 de 24 76338NP 06-17-20 Rev. A...
  • Página 16 Réinstaller le carénage – Reconnecter tout le câblage en premier. Puis réinstaller le carénage à l’aide de la visserie d’origine retirée aux étapes 1 et 2. ©2020 Horizon Global™ Corp. - Imprimé au Mexique Feuille 16 de 24 76338NP 06-17-20...
  • Página 17: Garantía Limitada De Por Vida

    TechnicalSupport@horizonglobal.com GARANTÍA LIMITADA DE POR VIDA Garantía limitada de por vida ("Garantía") Horizon Global ("nosotros", "nos" o "nuestro/a/s") Para evitar DAÑOS DE GRAVEDAD, A LA PROPIEDAD O LA MUERTE: garantiza al comprador original únicamente ("usted" o "su/s") que el producto estará libre de defectos significativos tanto en materiales como en mano de obra, con la excepción del desgaste...
  • Página 18: Equipo Necesario

    Instrucciones de instalación Escanear para instrucciones de la instalación paso por NÚMEROS DE PARTES: 76338, 84338, CQT76338 paso con FOTO, o visitar Sitio web: www.horizonglobal.com http://qr.towingproducts. net/qrproducts/qr- Assistance técnica: 800-632-3290 product TechnicalSupport@horizonglobal.com Aplicaciones: Tiempo de instalación: 75 min. Años Marca...
  • Página 19 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 0©2020 Horizon Global™ Corp - Impreso en México Hoja 19 de 24...
  • Página 20 T25, quitar 5 tornillos y el protector de calor. Repetir los pasos del lado del pasajero. Dejar a un lado los fijadores y el protector de calor para volver a instalarlos. 0©2020 Horizon Global™ Corp - Impreso en México Hoja 20 de 24...
  • Página 21 (2) tornillos. Colocar los fijadores a un lado para su reinstalación. moldura del receptáculo de la rueda. Quitar únicamente lo que se muestra en la Figura 2. 0©2020 Horizon Global™ Corp - Impreso en México Hoja 21 de 24 76338NP 06-17-20 Rev.
  • Página 22 Conservar los pernos para la instalación del enganche. Ver la Figura 1. Panel final Banda de apoyo viga de parachoques Pernos M12 existentes (8) lugares Figura 1 0©2020 Horizon Global™ Corp - Impreso en México Hoja 22 de 24 76338NP 06-17-20 Rev. A...
  • Página 23 4" de ancho x 4" de alto. Ver la Figura 3. Nota: Verificar que el área esté libre de todo el cableado eléctrico antes de recortar. Área a recortar 4” 4” Figure 3 0©2020 Horizon Global™ Corp - Impreso en México Hoja 23 de 24 76338NP 06-17-20 Rev. A...
  • Página 24 6. Volver a instalar la fascia: Volver a conectar todo el cableado primero. Luego, volver a instalar la fascia con las piezas que se quitaron en los pasos 1 y 2. 0©2020 Horizon Global™ Corp - Impreso en México Hoja 24 de 24...

Este manual también es adecuado para:

7633884338