Coolaroo 472801 Manual De Instrucciones

EXTERIOR
SHADE
by Coolaroo®
Congratulations on the purchase of your Exterior Shade by Coolaroo
entirety before installing your Shade.
(4) Idle end plug
(3) Headrail
(2) Crank plug
(5) Idle
end unit
(6) Wand
ADDITIONAL TOOLS NEEDED
20 minute set up
Drill with 3/16 in. bit
(approximate time)
Level
Tape measure
Pencil
MEASUREMENT GUIDE
36 in. 48 in. 60 in. 72 in.
PRODUCT WIDTH
(91 cm) (122 cm) (152 cm) (183 cm)
33 in. 45 in. 57 in. 69 in.
MATERIAL WIDTH
(84 cm) (114 cm) (145 cm) (175 cm)
OVERALL WIDTH
36 in. 48 in. 60 in. 72 in.
BRACKET-TO-
(91 cm) (122 cm) (152 cm) (183 cm)
BRACKET
1
INSTALL BRACKETS
Identify the Bracket-to-Bracket position of your Shade
A.
(Fig. 1).
Use the the center of the screw holes to allow for
B.
movement if necessary to provide a snug fit. Crank
unit bracket will be on the right side, and the Idle end
unit bracket should be on the left side; they cannot be
interchanged (Fig. 2).
NOTE: Do not tighten screws completely yet.
. Please be sure to read the manual in its
®
PARTS LIST
(1) Crank unit
1 Crank unit
2 Crank plug
3 Headrail
4 Idle end plug
(7) Shade
5 Idle end unit
6 Wand
7 Shade
(8) Bottom
rail
8 Bottom rail
96 in.
Fig. 1
(244 cm)
93 in.
Bracket-to-Bracket
(236 cm)
96 in.
(244 cm)
Fig. 2
Idle end unit bracket
Crank unit bracket
2
ATTACHING THE SHADE
Insert the Crank plug into the Crank unit (Fig. 3).
A.
Then insert the Idle end plug into the Idle end unit and
QTY
snap the Idle end plug securely into place (Fig. 4).
1
IMPORTANT: With the shade in place
1
adjust the brackets so they provide a snug
fit. Now go back and tighten the bracket
1
screws completely. The screws included
in your hardware kit are for use with
1
wood only. See your retailer for mounting
1
recommendations when attaching your
Shade to any other material.
1
1
CHANGE TO A TOP CEILING MOUNT
1
If you want your Shade to hang from the top (for
example, the ceiling), you will need to make a simple
change to your Crank unit and Idle end unit before
you install your Shade.
Remove the two screws from both brackets (Fig. 5).
A.
Turn the Crank unit 90° so the crank eyelet hangs
B.
straight down. Now turn the Idle end unit so the
opening is facing away from the window
(Fig. 6), then put the screws back in.
Retract your exterior shade when not in use, or before strong storms, to prevent damage.
MAINTENANCE: Your exterior Shade has been made of the finest materials
and, when properly cared for, will provide years of shade and privacy. To clean
your Shade, simply rinse with water, scrub with mild soap or any nonabrasive
cleaner, rinse and allow to dry. Call us for missing parts or mechanical problems.
Do not store Shade wet. In moist areas, roll Shade down frequently to air dry.
CAUTION: Use of solvents or abrasive cleaners may damage the fabric and will
void your warranty. Do not use bleach or chlorine.
GALE Pacific USA | www.coolaroousa.com | 1-800-560-4667
© by GALE Pacific Limited. All rights reserved. Coolaroo
INSTALLATION
INSTRUCTIONS
Fig. 3
Fig. 4
Snap Idle end plug
into Idle end unit
Fig. 5
Fig. 6
Rotate
Idle end
unit 90°
Questions or Comments? Contact us at:
is a registered trademark of GALE Pacific Limited.
®
Crank plug
Remove screws
Rotate
Crank
unit 90°
Order replacement
parts online:
www.coolaroousa.com