Technical Specifications - HK Audio PREMIUM PR:O Serie Manual De Instrucciones

PREMIUM PR:O passive 2.0
2.2 PR:O 8 / 10 X / 12 / 15 / 15 X in Satellite Mode with the
PR:O 18 S or the PR:O 210 S
First connect the speaker output of the powered mixer or power amp to the
subwoofer's input, and then connect the subwoofer's SATELLITE OUT to
the PR:O 8, PR:O 10 X, PR:O 12, PR:O 15 and PR:O 15 X full-range cabinet's
input (IN).
Power Mixer
or
Poweramp
Note: The nominal impedance of systems consisting of a combination
of PR:O 18/210 S and PR:O 8, PR:O 10 X, PR:O 12, PR:O 15 and PR:O 15 X
cabinets is 4 ohms!
2.3 PR:O 10 X, PR:O 12 M and PR:O 15 X
Monitor Amp
4 Technical Specifi cations
Model PR:O 8
Frequency response 89 Hz – 19 kHz
+/- 3 dB
Frequency response 63 Hz – 19 kHz
-10 dB
Max SPL @ 10% THD* 122 dB
Axial sensitivity 97 dB
1 W @ 1m*
Power handling, peak 1200 W
Power handling, 600 W
program
Power handling, nom. 300 W
(RMS)
Speaker 1x 8"
HF driver 1"
Impedance 8 ohms
HF protection Dyn. protective circuit
(passive)
Horn dispersion 80° x 80° CD horn
X-over frequency 2.5 kHz, 12 dB/oct.
Connectors 2x Speakon NL4
Angles up -
Pole mount MonoTilt 3°
Rigging/ pick points 3x M8
Casters -
Dimensions (W x 27 x 42 x 27.5 cm
H x D)
Weight 10 kg / 22.1 lbs
Recommended power output: Use amps that deliver between 600 and 800 watts RMS per channel @ 4 ohms to drive PREMIUM PR:O enclosures. Ensure the amp's peak power
output is at least 1,200 watts per channel @ 4 ohms to leave enough headroom for dynamic musical signals.
*) All measurements taken under half-space conditions. **) Active x-over frequency at 24 dB/ octave
4
Poweramp
PR:O 10 X PR:O 12
95 Hz – 19 kHz 68 Hz – 19 kHz
80 Hz – 19 kHz 60 Hz – 19 kHz
126 dB 128 dB
99 dB 104 dB
1200 W 1200 W
600 W 800 W
300 W 400 W
1x 10" 1x 12"
1" 1"
8 ohms 8 ohms
Dyn. protective circuit Dyn. protective circuit
90° x 60° CD horn 60° x 40° CD horn
2.2 kHz, 12 dB/oct. 2 kHz, 12 dB/oct.
2x Speakon NL4 2x Speakon NL4
30° -
DuoTilt 3°/7° DuoTilt 3°/7°
3x M8 3x M8
- -
32 x 48.5 x 30 cm 41 x 58 x 37 cm
12.9 kg / 28.4 lbs 18.5 kg / 40.8 lbs
Connect the monitor power amp's speaker output to the PR:O 10 X, PR:O 12
M und PR:O 15 X monitor's input (IN). Depending on the type of power amp
or powered mixer that you are using, several PR:O 10 X, PR:O 12 M und PR:O
15 X monitors can be connected in parallel to one power amp channel.
Poweramp
Note:
• When two PR:O 10 X, PR:O 12 M and PR:O 15 X monitors are -connected in
parallel, overall impedance is 4 ohms.
• When three PR:O 10 X, PR:O 12 M and
PR:O 15 X monitors are connected in parallel, overall impedance is 2.7
ohms.
• When four PR:O 10 X, PR:O 12 M and PR:O 15 X monitors are connected in
parallel, overall impedance is 2 ohms.
Caution: Do not allow the overall nominal impedance of the connected
monitors to fall below the power amp channel's minimum impedance! If
it does, you risk destroying the power amp!
PR:O 12 M PR:O 15
70 Hz – 19 kHz 60 Hz – 19 kHz
63 Hz – 19 kHz 53 Hz – 19 kHz
128 dB 128 dB
104 dB 104 dB
1200 W 1200 W
800 W 800 W
400 W 400 W
1x 12" 1x 15"
1" 1"
8 ohms 8 ohms
Dyn. protective circuit Dyn. protective circuit Dyn. protective circuit -
60° x 40° CD horn 60° x 40° CD horn
2 kHz, 12 dB/oct. 2 kHz, 12 dB/oct.
2x Speakon NL4 2x Speakon NL4
30° -
- DuoTilt 3°/7°
- 3x M8
- -
39 x 56 x 38 cm 47.5 x 62 x 41.5 cm
16.5 kg / 36.4 lbs 22.5 kg / 50.8 lbs
PR:O 15 X PR:O 210 S
60 Hz – 19 kHz 60 Hz – 150 Hz
53 Hz – 19 kHz 40 Hz – 150 Hz
128 dB 126 dB
104 dB 101 dB
1200 W 1500 W
800 W 1,000 W
400 W 500 W
1x 15" 2x 10"
1" -
8 ohms 4 ohms
60° x 40° CD horn -
2 kHz, 12 dB/oct. 150 Hz, 12 dB/oct. 150 Hz, 12 dB/oct.
2x Speakon NL4 2x Speakon NL4
45°
DuoTilt 3°/7° 2x M20
3x M8 -
- -
47.5 x 62 x 45 cm 36 x 61 x 53 cm
22 kg / 48.5 lbs 26 kg / 57.3 lbs
PR:O 18 S
48 Hz – 150 Hz
38 Hz – 150 Hz
129 dB
104 dB
1,500 W
1,000 W
500 W
18"
-
4 ohms
-
-
2x Speakon NL4
1x M20
-
Optional 100 mm
53 x 61 x 64 cm
40 kg / 88.2 lbs