General Descriptions - Cebora POWER ROD 1535 Manual De Instrucciones

1.2 Protect yourself from electric shock by insulating
yourself from work and ground.
1.3 Disconnect input plug or power before working on
machine.
2 Breathing welding fumes can be hazardous to your
health.
2.1 Keep your head out of fumes.
2.2 Use forced ventilation or local exhaust to remove
fumes.
2.3 Use ventilating fan to remove fumes.
3 Welding sparks can cause explosion or fire.
3.1 Keep flammable materials away from welding.
3.2 Welding sparks can cause fires. Have a fire extin-
guisher nearby and have a watchperson ready to use
it.
3.3 Do not weld on drums or any closed containers.
4 Arc rays can burn eyes and injure skin.
4.1 Wear hat and safety glasses. Use ear protection and
button shirt collar. Use welding helmet with correct
shade of filter. Wear complete body protection.
5 Become trained and read the instructions before
working on the machine or welding.
6 Do not remove or paint over (cover) label.

2 GENERAL DESCRIPTIONS

2.1 SPECIFICATIONS
This welding machine is a constant current generator built
using INVERTER technology, designed to weld with covered
electrodes and for TIG procedures, with contact starting.
IT MUST NOT BE USED TO DEFROST PIPES.
2.2 EXPLANATION OF THE TECHNICAL SPECIFI-
CATIONS LISTED ON THE MACHINE PLATE.
This machine is manufactured according to the following
international standards: IEC 60974.1 - IEC 60974.3 -IEC
60974.10 CL. A - IEC 61000-3-12 - IEC 61000-3-11 (see
note 2).
N°. Serial number, which must be indicated on any
type of request regarding the welding machine.
Single-phase static transformer-rectifier
frequency converter.
Drooping characteristic.
SMAW. Suitable for welding with covered electrodes.
TIG Suitable for TIG welding.
U0. Secondary open-circuit voltage
X. Duty cycle percentage. % of 10 minutes during
which the welding machine may run at a certain
current without overheating.
I2. Welding current
U2. Secondary voltage with current I2
U1. Rated supply voltage
The machine has an automatic supply voltage selector.
1~ 50/60Hz 50- or 60-Hz single-phase power supply
I1 max. This is the maximum value of the absorbed current.
I1 eff. This is the maximum value of the actual current
absorbed, considering the duty cycle.
IP23S Protection rating for the housing.
Grade 3 as the second digit means that this
equipment may be stored, but it is not
suitable for use outdoors in the rain, unless
it is protected.
S
Suitable for hazardous environments.
Note:
1- The machine has also been designed for use in envi-
ronments with a pollution rating of 1. (See IEC 60664).
2- This equipment complies with IEC 61000-3-11 provided
that the maximum permissible system impedance Zmax
is less than or equal to 0,29 (art. 261) - 0,362 (art. 257)
at the interface point between the user's supply and the
public system. It is the responsibility of the installer or
user of the equipment to ensure, by consultation with the
distribution network operator if necessary, that the equip-
ment is connected only to a supply with maximum per-
missible system impedance Zmax less than or equal to
0,29 (art. 261) - 0,362 (art. 257).
2.3 DESCRIPTION OF PROTECTIVE DEVICES
2.3.1 Thermal protection
This equipment is protected by a thermostat. When the ther-
mostat is tripped, the machine stops delivering current but
the fan continues to run. The yellow led (B) lights to indicate
when it is tripped.
Do not shut off the welding machine until the led has gone off.
2.3.2 Motor-driven generators
These must have a power equal to or greater than 6KVA, and
must not deliver a voltage greater than 265V.
2.3.3 Protection against short-circuits (antistick)
If a short-circuit occurs lasting more than two seconds when
welding with coated electrodes, the current is reduced to
harmless levels.
3 INSTALLATION
This must be carried out by skilled personnel. All connections
must be carried out according to current regulations, and in
full observance of safety laws (regulation CEI 26-23 - CEI
CLC 62081).
• Make sure that the supply voltage matches the voltage indi-
cated on the specifications plate.
• When mounting a plug, make sure it has an adequate capa-
city, and that the yellow/green conductor of the power supply
cable is connected to the earth pin.
WARNING! Extension cords of up to 30m must have a cross-
section of at least 2.5 mm2.
3.1 DESCRIPTION OF THE EQUIPMENT
A) Current adjustment.
B) Yellow led (see 2.3).
C) Power ON led.
D) Output terminal (-).
E) Output terminal (+).
F) Switch.
G) Mains cable.
H) Connector (Art. 261).
7