Stanley FATMAX FME380 Manual Del Usuario página 11

Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off (fig. A)
Note:Before engaging the on/off switch, check the saw blade
to see if it is fitted properly and runs smoothly, and the blade
clamp screw is well tightened.
Push the trigger lock and shoe release button button (10)
u
to release the trigger.
Switch on tool by pulling trigger switch (1).
u
Switch off tool by releasing trigger switch (1).
u
Adjusting cutting depth (0-28,5 mm) (fig.B)
Loosen clamp (3).
u
Set desired cutting depth using scale (2).
u
Tighten clamp (3)
u
For an optimal quality cut, the saw blade should not
u
extend more than 3 mm below the workpiece
Be aware that the actual depth of cut of the diamond
u
disc differs approx. 2 mm from the depth of cut indicated
on scale (2).
Note: Always make trial cuts first to verify actual line of
cut.
Dust suction (fig.C)
connect vacuum cleaner hose (19) to connection (13) and
u
vacuum cleaner as illustrated.
Warning! Never let the vacuum cleaner hose interfere with
the lower guard or the cutting operation.
Warning! Do not use vacuum cleaner when cutting metal.
Changing saw blade (fig. D - G)
Warning! Before changing blades or performing any mainte-
nance, ensure the tool is off and disconnected from the power
source.
Set cutting depth to the maximum (fig. D).
u
Use hex key (15) provided.
u
Push spindle-lock button (14) and hold (Fig. E).
u
Remove blade bolt (9) by turning hex key (15)
CLOCKWISE (= in same direction as arrow imprinted on
the guard) (Fig. F).
Release spindle-lock button (14).
u
Remove flange (8).
u
Press button (10) with your thumb
u
Lift up foot (7) and remove saw blade.
u
Install new blade making sure that rotation of blade is in
u
same direction as arrow imprinted on the guard.
Mount flange (8).
u
Firmly tighten blade bolt (9) by turning hex key (15)
u
COUNTER-CLOCKWISE while pushing spindle-lock
button (14).
Release spindle-lock button (14).
u
(Original instructions)
Operating the tool
(fig. H - M)
Set desired cutting depth.
u
Connect plug to power source.
u
Press button (10) with your thumb.
u
Place tool with front end of foot flat on workpiece.
u
Tilt tool forward with line-of-cut indicator (20) lined up with
u
desired line of cut marked on the workpiece (fig. H).
Ensure that the saw teeth are not engaged into the work-
u
piece.
Switch on the tool.
u
The tool should run at full speed before the blade enters
u
into the workpiece.
Do not force the tool (apply light and continuous
u
pressure in order to avoid overheating the blade tips and,
in case of cutting plastics, melting the plastic material).
While working, always hold the tool at the insulated grip
u
area(s).
After completing the cut switch off tool by releasing trigger
u
(1).
Ensure that the blade has come to a complete standstill,
u
before you lift the tool from the workpiece.
Electronic Function. Laser beam action (Fig.I)
Caution! When not in use, be sure to turn off the laser.
Never look into the laser beam directly; laser beam may injure
your eyes.
LASER RADIATION: DO NOT STARE INTO THE BEAM or
any CLASSII LASER PRODUCTS.
Before shifting the laser line or performing maintenance
adjustment, be sure to unplug the tool.
To turn the laser on/off, toggle the switch (12a) on the
u
back of the laser housing.
Cleaning of the lens for the laser light
If the lens for the laser light becomes dirty, or sawdust ad-
heres to it in such a way that the laser line is no longer easily
visible, unplug the saw and clean the lens carefully with a
damp, soft cloth. Do not use solvents or any petroleum based
cleaners on the lens.
Note: When laser line is dim and almost or entirely invisible
because of the direct sunlight in the indoor or outdoor window
near your work area, relocate the work area to a place not
exposed to direct sunlight.
Note: All of the adjustments for the operation of this machine
have been carried out at the factory.
Caution: Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure. The use of optical instruments
with this product will increase eye hazard. Do not attempt to
repair or disassemble the laser. If unqualified persons attempt
to repair this laser product, serious injury may result.
ENGLISH
11