Important Safety Notes - Martin Yale intimus 170 Serie Instrucciones De Uso

GB
<< The machine may not be operated by more
than one person at any given time!
T he machine was designed for safe operation
by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.).
<< Keep children away from the machine.
This machine's design and safety concept
are based on adult dimensions (inlet guide,
safety cut-off switches, etc.) to ensure that it
can be operated safely by adults only.
<< Repairs may only be performed by trained
personnel.
PAPER JAM:
If too much paper is fed to the cutting system the
machine will react as follows:
- The cutting system blocks and then stops.
- The pilot lamp of the stop-putton „S" (3) (fig. 2)
will light.
Proceed as follows:
- Briefly operate the pushbutton switch for reverse
(4) (fig. 2).
- The cutting mechanism then runs backwards
and returns the excess material.
- Remove excess paper from the machine and
continue shredding with less paper.
Important: After any paper jam, make certain the
cutting mechanism is free to operate in both free
(particles have jammed between the cutters and
the scraper), spray some of the special oil supplied
with the machine through the feed slot onto the
cutting mechanism while alternating between
forward and reverse modes until the machine is
free.
SPECIAL ACCESSORIES
Description
Plastic bag, 700 x 500 x 1200 x 0,06 mm
Lubrication bottle, 125 ml
Second deposit tray cpl., silver gray
Second deposit tray cpl., chrome plated
Receptacle, 625 x 480 x 660 mm
Note: For orders of special accessories and spare parts, please contact your dealer.

IMPORTANT SAFETY NOTES

MALFUNCTION
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. Turn the machine off with
the rocker switch (1) (fig. 1).
Allow the motor to cool down for 15 to 20 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the following:
- is the plug connected to the mains?
- is the rocker switch (1) on?
- is the door closed?
- is the collecting bag full?
The bag has to be emptied.
- is there a paper jam?
Follow the instructions under „paper jam".
- has the motor been overloaded?
Wait until the motor has cooled, and then restart.
If none of the above applies, please contact
your dealer.
<< Keep all loose articles of clothing,
ties, jewelery, long hair or other
loose objects away from opening,
injury may result!
<< Never insert fingers into opening.
Serious injury may result!
STOP << In case of danger switch the machine
off with the mains switch, or with the
emergency switch, or unplug the
machine.
<< Always unplug the machine from the
mains power supply before opening the
machine.
MAINTENANCE CUTTING BLOCK:
After approximately 15 minutes of continuous
use, run the cutting system in reverse for 15 to 20
seconds and spray some of the enclosed Special
Oil onto the cutting system.
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched
off over night (rocker switch (1) (fig. 1).
Cutting width:
Cutting capacity:
Supply voltage:
Pre-fusing:
230V/50Hz:
240V/50Hz:
120V/60Hz:
100V/50/60Hz:
Working width:
Noise level:
Power:
Order-No.
Dimensions:
99954
Width:
99943
Depht:
30712
Height:
30702
Weight:
75987
5
MAINTENANCE
TECHNICAL DATA
0.7x9.5 mm (cross-cut)
12-14 sheets (70 g/m
230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
16 A
13 A
20 A
20 A
300 mm
approx. 70 dB(A)
1.1 kW
700 mm
550 mm
1115 mm
approx. 142 kg
2 )