Configuration - Vimar ELVOX 41017 Manual Del Instalador

41017
Transponder reader for access control,
white LED backlighting, 1 input that can be
enabled for an additional button, 1 NO relay
output, to be completed with front panel.
1. Description
The device allows access control and actuator control by
RFID card. Four possible operating modes, according to
type of installation: standalone, slave-2wire, eipvdes (IP
Video-Door Entry System), o
dalone and slave-2wire operating modes, the configuration
management and update software to be used is SaveProg;
and
for eipvdes slave-eipvdes, Video Door IP Manager is
to be used.
In standalone mode (factory default setting), recognition of
a previously registered card commands activation of output
F1. It is also possible to enable input CA for the connection
of an additional pushbutton and directly command output F1.
In this mode, SaveProg can be used to register cards and
configure the device.
In slave-2wire mode, the device must be connected to an
electronic audio or audio/video module in the Pixel 2-wire
series using specific wiring (connectors f or g). The above
description for standalone mode applies. Alternatively, out-
put F1 may be used to control any other output (relay/lock)
of the audio or audio/video module or other auxiliary modules
of the external unit.
In eipvdes mode, the device must be connected directly
(via RJ45 interface) to a network on which an Elvox IP vid-
eo door entry service is provided. Device programming and
configuration operations are performed using Video-Door IP
manager. Each registered card, and also input CA, can be
associated with activation of an actuator in the video door en-
try system (including the local F1 relay). Alternatively, CA can
be configured as the sensor input for the "door open" signal.
In slave-eipvdes mode, the device must be connected to
an electronic audio or audio/video module in the Pixel IP se-
ries using specific wiring (connectors f or g). The functional
characteristics, the programming and the configuration op-
erations are the same as described for the eipvdes mode.
In the factory default setting (standalone mode), the device,
if connected to an Elvox IP video door entry system, can
be identified and configured using Video-Door IP Manager.
Once the first configuration has been completed, the oper-
ating mode will be set as eipvdes
2wire and slave-eipvdes operating modes, slave mode
must be specifically set using SaveProg. Any of the support-
ed operating modes may be set using SaveProg at any time.
The device is compliant with the ISO 14443A/MIFARE
standard: MIFARE™ CLASSIC (1K e 4K), MIFARE ULTRA-
LIGHT™ (ULTRALIGHT EV1/ULTRALIGHT C) and MIFARE
DESFire™ (DESFIRE EV1 2K/4K/8K).
8
r
slave-eipvdes. For the stan-
.
However, for the slave-
2. Characteristics
• Power supply:
1) from the electronic audio or audio/video module,
via specific wiring
modes);
2) from additional power supply unit on terminals 5V+ and
5V- (all operating modes);
3) Power-over-Ethernet Class 0 (IEEE 802.3-2012) via
RJ45 interface. NOTE: The RJ45 network interface
is to be connected exclusively to a SELV (Safety Ex-
tra-Low Voltage) network. The Power-over-Ethernet
power supply unit (PSE) must provide electrical insu-
lation between any accessible conductor including the
earth wire, if there is one, and all the contacts of the
network ports, including those not used by the PSE or
by the device to be installed (eipvdes mode).
• Maximum power consumption: 250 mA at 5V.
• Average PoE consumption: 2.5 W.
• Operating temperature range: -25 °C / +55 °C.
• Ingress protection rating: IP54.
• Protection rating against impact: IK08.
• Operating frequency: 13.56 MHz.
• Operating distance: up to 1 cm.
•
Compatible with Vimar programmable transponder card
(art. 01598).
3. Standalone and slave-2wire
A maximum of 2000 user or installer cards can be registered
in total. The first type can be used to activate the configured
actuator, while the second can be used to register new user
card without having to use SaveProg (manual registration).
By default, only the use of MIFARE CLASSIC 1K cards is
enabled. Using SaveProg, it is possible to enable the use of
other types of card.

3.1 Configuration

Connect the device to the PC using a USB cable. Refer to the
SaveProg documentation for specific details. It is possible to:
• Set the operating mode: standalone, slave-2wire,
slave-eipvdes or eipvdes.
• Add and remove user and installer cards.
• Associate each card with a name and an extension
number in order to simplify removal. The cards are
saved on the device with a unique, sequential recog-
nition ID. The archive of a user's card-name pairings is
saved by SaveProg on the PC being used, when pro-
gramming the device.
EN
(
slave-2wire and slave-eipvdes
modes