Product Operation - LUND 67900 Manual Del Usuario

GB

PRODUCT OPERATION

Preparing the product for operation
Remove the product from its packaging, remove all packaging components, and wash all drive unit components according to the
instructions found in the "Product maintenance" section.
Set the product according to the instructions.
Install the meat grinder attachment body or the grating and shredding attachment body. The body should be mounted by pushing
it at an angle to the mounting socket and then rotating it so that the inlet opening faces upwards (II).
During installation, you will hear the characteristic sound of the fi xing ratchet which secures the attachment body in the socket.
In case of installation problems, you can always press and hold the lock button, fi x the attachment and release the lock button.
Ensure the assembly has been correct.
A correctly installed attachment body cannot be removed except by pressing the lock button (III) beforehand. Next, rotate the
attachment body by a small angle and remove it from the mounting socket.
Meat grinder attachment
Connect the attachment body to the mounting socket. Insert the grinding auger into the body so that the axis of the drive fi ts into
the opening of the auger (IV).
Place the blade on the square socket, the cutting edges should be directed to the outside of the attachment (V).
Apply the strainer. The strainer has positioning tabs on the edge, which should fi t into the notches in the front of the attachment (VI).
The strainers supplied with the product have openings of diff erent diameters. The smaller the openings, the more fi nely the food
will be ground.
Caution! Only one strainer can be fi tted at a time.
Screw the fi xing nut (VII) onto the outlet thread of the attachment.
Install the feed tray (VIII) on the inlet opening.
Check that the pusher can be easily inserted and removed from the inlet opening.
Sausage-fi lling attachment (IX)
Assemble like the meat grinding attachment, but before screwing on the fi xing nut, install the sausage-fi lling attachment.
Juice-squeezing attachment (X)
Connect the attachment body to the mounting socket and insert the grinding auger into the body.
Insert the fi lter into the juice-squeezing cap and then the conical auger. Attach the cap to the attachment body and secure it with
a nut. The tomato-squeezing attachment is equipped with positioning tabs, which should fi t into the notches in the front of the
attachment.
Tighten the adjusting screw at the front of the socket, but do not tighten it fully.
Place a cap on top of the attachment to prevent the juice from spilling out during squeezing.
There will be juice coming out through the small openings in the cap, so you should put a container of such a diameter as to
prevent the juice from spilling over during operation.
The fruit pulp will be squeezed out of the front opening of the cap. The tightness of the screw must be adjusted by observing
the results of the extrusion. Do not allow juice and pulp to clog the inside of the attachment. Excessive juice build-up inside the
attachment can cause fl ooding of the drive, which can damage the product and cause electric shock.
If the pulp coming out of the opening is excessively dry, loosen the screw slightly. This will help avoid clogging of the attachment.
Fruits with a higher juice content should be squeezed with a more-tightened screw. Less juicy fruit should be squeezed with a
less-tightened screw.
Kebbe attachment (XI)
Connect the attachment body to the mounting socket and insert the grinding auger into the body.
The rear part of the kebbe cap is equipped with positioning tabs, which should fi t into the notches in the front of the attachment.
Insert the front part of the socket into the kebbe cap and secure by tightening the fi xing nut.
Grating and shredding attachment (XII)
The attachment has a separate body and a separate pusher.
Install the attachment body into the drive socket.
Slide the drum into the body. The openings in the drum are very sharp and must be handled with care to avoid injury.
The attachment axis tabs should align with the notches in the opening in the rear wall of the drum (XIII).
Check that the pusher can be easily inserted and removed from the inlet opening.
Caution! Do not use the grinder attachment pusher in this attachment.
The product is equipped with three types of drums. Two drums with round openings are used for grating. The larger the openings,
the larger the shavings. The drum with rectangular openings is used for shredding.
After mounting the selected attachment, place a container under its outlet. The product is ready for use.
O R I G I N A L I N S T R U C T I O N S
14