Definitions: Safety Guidelines; Electrical Safety; Personal Safety - DeWalt D25501 Traducido De Las Instrucciones Originales

EngLIsH
These products also comply with Directive 2014/30/EU and 2011/65/EU. For
more information, please contact D
to the back of the manual.
The undersigned is responsible for compilation of the technical file and
makes this declaration on behalf of D
Markus Rompel
Director Engineering
D WALT, Richard-Klinger-Straße 11,
e
D-65510, Idstein, Germany
22.06.2016
WARNING: To reduce the risk of injury, read the instruction manual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which,
if not avoided, may result in property damage.

Denotes risk of electric shock.

Denotes risk of fire.
General Power Tool Safety Warnings

WARNING: Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in electric shock,
fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1) Work area safety
a ) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b ) Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c ) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.

2) Electrical safety

a ) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
b ) Avoid body contact with earthed or grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c ) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d ) Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat,
18
WALT at the following address or refer
e
WALT.
e
oil, sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e ) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f ) If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.

3) Personal safety

a ) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power tool
while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools
may result in serious personal injury.
b ) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c ) Prevent unintentional starting. Ensure the switch is in the off
position before connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the
switch on invites accidents.
d ) Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
e ) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g ) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected
and properly used. Use of dust collection can reduce dust-
related hazards.
4) Power tool use and care
a ) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better and
safer at the rate for which it was designed.
b ) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c ) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users.
e ) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool's operation. If damaged, have the
power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control.
g ) Use the power tool, accessories and tool bits etc., in accordance
with these instructions taking into account the working
conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a
hazardous situation.