Protecting The Environment - DeWalt D25501 Traducido De Las Instrucciones Originales

EngLIsH
3. D25601, D25602, D25603 only: Set the electronic speed and impact
control dial .
7
4. Fit and adjust the side handle 3
5. Mark the spot where the hole is to be drilled.
6. Place the drill bit on the spot and switch on the tool.
7. Always switch off the tool when work is finished and
before unplugging.
Drilling with a Core Bit (Fig. A)
1. Insert the appropriate core bit.
2. Assemble the centerdrill into the core bit.
3. Set the mode selector switch
6
4. D25601, D25602, D25603 only: Turn the electronic speed and impact
control dial 7 to a medium or high speed setting.
5. Fit and adjust the side handle 3
6. Place the centerdrill on the spot and switch on the tool. Drill until the
core penetrates into the concrete approximately 1 cm.
7. Stop the tool and remove the centerdrill. Place the core bit back into the
hole and continue drilling.
8. When drilling through a structure thicker than the depth of the core
bit, break away the round cylinder of concrete or core inside the bit at
regular intervals.
To avoid unwanted breaking away of concrete around the hole, first drill
a hole the diameter of the centerdrill completely through the structure.
Then drill the cored hole halfway from each side.
9. Always turn the tool off when work is finished and before unplugging.
Chipping and Chiselling (Fig. A)
D25501, D25601, D25602, D25603, D25820,
D25831
1. Insert the appropriate chisel and rotate it by hand to lock it into one of
18 positions.
2. Set the mode selector switch 6
3. D25601, D25602, D25603, D25831 only: Set the electronic speed and
impact control dial 7 .
4. Fit and adjust the side handle 3
5. Turn the tool on and start working.
6. Always turn the tool off when work is finished and before unplugging.
MAINTENANCE
Your D WALT power tool has been designed to operate over a long period
e
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories. Be sure the trigger switch is in the OFF position. An
accidental start-up can cause injury.
Brushes (Fig. C)
The carbon brushes are not user-serviceable. Take the tool to an authorized
D WALT repair agent.
e
The yellow brushwear indicator LED
are nearly worn out. After a further 8 hours of use or after the brushes have
completely worn out, the motor will automatically be shut off.
Tool maintenance needs to be carried out as soon as the service
indicator 18 lights up.
Lubrication
Your power tool requires no additional lubrication.
22
.
to the hammerdrilling position.
.
to the hammering only position.
.
17 lights up when the carbon brushes
Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air
as often as dirt is seen collecting in and around the air vents. Wear
approved eye protection and approved dust mask when performing
this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning
the non-metallic parts of the tool. These chemicals may weaken the
materials used in these parts. Use a cloth dampened only with water
and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered by D
have not been tested with this product, use of such accessories with
this tool could be hazardous. To reduce the risk of injury, only D
recommended accessories should be used with this product.
Consult your dealer for further information on the appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be recovered or
recycled reducing the demand for raw materials. Please recycle
electrical products and batteries according to local provisions. Further
information is available at www.2helpU.com.
WALT,
e
WALT
e