Optional Accessories - DeWalt DCF801 Traducido De Las Instrucciones Originales

EnGLIsh
DCF902
Precision Wrench™ Mode
Lo Mode
Hi Mode
Quick-Release Chuck (Fig. F)
DCF801

WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessory prior to use to ensure that it con tains
no cracks.
nOTE: The chuck accepts 6.35 mm hex bit tips only. Using
25 mm bits allows better access in tight spaces.
Place the forward/reverse button
position or remove battery pack before changing accessories.
To install an accessory, push accessory to fully insert into
chuck . The chuck collar does not need to be pulled up to
6 5
lock accessory in place.
To remove an accessory, pull the chuck collar away from the
front of the tool. Remove the accessory and release the collar.
Anvil With Hog Ring (Fig. G)
DCF902

WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessory prior to use to ensure that it contains
no cracks.

CAUTION: Inspect anvils, detent pins, and hog rings prior
to use. Missing or damaged items should be replaced
before use.
Place the forward/reverse button
position or remove battery pack before changing accessories.
To install an accessory on the hog ring anvil, firmly push
accessory onto the anvil 10 . The hog ring
allow the accessory to slide on. After accessory is installed, the
hog ring applies pressure to help provide accessory retention.
To remove an accessory, grasp the accessory and firmly pull
it off.
Usage
Your impact tool generates the following maximum torque:
Cat # Nm
DCF801 163
DCF902 168

CAUTION: Ensure fastener and/or system will withstand
the level of torque generated by the tool. Excessive torque
may cause breakage and possible personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press switch to start operation. Release the switch to stop
operation. Always check torque with a torque wrench, as
the fastening torque is affected by many factors including
the following:
32
Precision Wrench™
Low Speed Impacting
High Speed Impacting
in the locked off (centre)
4
4 in the locked off (centre)
11 compresses to
Ft.-Lbs. In.-Lbs
120.8 1450
125 1500
Voltage: Low voltage, due to a nearly discharged
-
battery, will reduce fastening torque.
- accessory size: Failure to use the correct accessory size
will cause a reduction in fastening torque.
- Bolt size: Larger bolt diameters generally require
higher fastening torque. Fastening torque will also vary
according to length, grade, and torque coefficient.
Bolt: Ensure that all threads are free of rust and other
-
debris to allow proper fastening torque.
- Material: The type of material and surface finish of the
material will affect fastening torque.
- Fastening Time: Longer fasten ing time results in
increased fastening torque. Using a longer fastening
time than recom mended could cause the fasteners to
be overstressed, stripped or damaged.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.

Optional Accessories


WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
WALT recommended
e