Fein ABLK18-1.3TE Manual De Instrucciones página 16

OBJ_BUCH-0000000259-001.book Page 16 Thursday, May 12, 2016 3:40 PM
en
16
Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
Use and handling of the battery (battery pack).
To avoid hazardous situations such as burns, fire, explo-
sion, skin injuries, and other injuries when handling the
battery, observe the following instructions:
Batteries must not be disassembled, opened or reduced
in size. Do not subject batteries to mechanical impact or
shock. Hazardous vapours and fluid can escape in case of
damage and improper use of the battery. The vapours can
irritate the respiratory system. Liquid ejected from the
battery may cause skin irritations or burns.
When battery fluid from a damaged battery has come into
contact with objects close by, check the respective com-
ponents, clean them or replace them as required.
Keep the battery away from heat and fire. Do not store the
battery in direct sunlight.
Do not remove the battery from its original packaging
until it is going to be used.
Before any work on the machine itself, remove the bat-
tery from the power tool. If the power tool accidentally
starts, there is danger of injury.
Remove the battery only when the power tool is switched
off.
Keep the battery away from children.
Keep the battery clean and protect it against moisture
and water. Clean contaminated battery terminals and
power tool connections with a dry, clean cloth.
Use only intact original FEIN batteries that are intended
for your power tool. When working with and charging
incorrect, damaged, repaired or reconditioned batteries,
imitations or other brands, there is danger of fire and/or
explosion.
Follow the safety warnings in the operating instructions
of the battery charger.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Operating Instructions.
Guide the power tool toward the work piece only
when switched on.
While cutting, hold the power tool as upright as possible
to the work-piece surface.
Guide the power tool uniformly and with light feed in the
cutting direction. Excessive feed reduces the tool life of
the application tools.
Do not cut steel sheets where welded. Do not cut lay-
ered sheets exceeding the max. work-piece thickness.
To increase the tool life of punch and die, it is recom-
mended to apply a lubricating agent alongside the
intended cutting line:
– For cuts in steel sheet: Cutting paste or cutting oil,
– For cuts in aluminium: Petroleum.
For inside cuts, a pilot hole is required; see "Technical
Data" for diameters.
Do not switch the power tool off until after having
removed it from the cutting path.
The symptom for worn punches and dies are a clearly
increased feed force at lower working progress.
Punch and die cannot be reground.
Handling the battery.
Operate and charge the battery only within the battery
operating-temperature range of 0°C – 45°C (32°F –
113°F). At the beginning of the charging procedure, the
battery temperature must be within the battery operat-
ing-temperature range.
LED indica- Meaning
tor
1 – 4 green Percentage of
LED charge condi-
tion
Continu- Battery is
ous red almost empty
light
Red flash- Battery is not
ing light ready for
operation
The real percentage of the battery charge condition is
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor prior
to the battery being deep discharged.
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air.
Lightly grease the sliding surfaces between die
holder and punch.
The current spare parts list for this power tool can be
found in the Internet at www.fein.com.
If required, you can change the following parts yourself:
Application tools
Activity
Operation
Charge battery
Bring the battery into
the battery operating-
temperature range, then
charge