Additional Safety Information - DeWalt DWE1622 Manual De Instrucciones

into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Additional Safety Rules for Drill Presses
• Keep your fingers well out of the drill area.
• Always use the drill guard.
• Always use the safety chain.
The magnetic stand is suitable for use on steel
•
with a thickness starting from 10 mm, with zero
air gap between the magnet core surface and the
mounting surface. Curvature, coats of paint and surface
irregularities will create an air gap. Keep the air gap to
a minimum.
Always place the machine on a flat surface. Do not
•
clamp the stand on small or irregularly shaped objects.
• Always place the machine on a surface that is clear
of shavings, chips, swarf and surface dirt.
• Keep the magnet clean and free of debris and swarf.
• Do not switch on the machine until it has been
mounted and installed according to the instructions.
Do not switch on the machine before having checked
•
that the magnetic stand has been tightened firmly
to the mounting surface.
• Adjust the table or depth stop to prevent the
drill from entering the workpiece. Do not perform
any design, assembly or construction activities on the
workpiece while the machine is switched on.
Before switching on the machine, make sure the
•
accessory has been mounted correctly.
• Always use the recommended speed for the
accessories and the material.
• Do not use the machine on the same workpiece on
which electric welders are being used.
Use only an appropriate cutting fluid. Use a general
•
non-oil based metal cutting coolant diluted with water.
• Do not use liquid cutting fluids while drilling
vertically or overhead. Dip the cutter in cutting paste or
apply an appropriate spray for these applications.
• Do not pour cutting fluid into the reservoir while it
is mounted in the bracket. Do not allow cutting fluid to
enter the drill motor.

Additional Safety Information


WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power
•
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.

WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
• Do not operate this tool for long periods of time.
Vibration caused by tool action may be harmful to your
hands and arms. Use gloves to provide extra cushion and
limit exposure by taking frequent rest periods.
• An extension cord must have adequate wire size
for safety. The smaller the gauge number of the wire,
the greater the capacity of the cable, that is, 16 gauge
has more capacity than 18 gauge. An undersized cord
will cause a drop in line voltage resulting in loss of power
and overheating. When using more than one extension
to make up the total length, be sure each individual
extension contains at least the minimum wire size. The
following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The lower the gauge number, the
heavier the cord.
ENGlIsh
21